background image

60

References

A. Specifications

BU2002RWL

BU3002RWL

BU5002RWL

Operation method

Full-time inverter supply method (high efficiency)

AC input Rated input voltage

AC200/208/220/230/240V

Startup voltage range

200V mode: 160±2 to 288±2 VAC, 208V mode: 167±2 to 278±2 VAC

220V mode: 176±2 to 278±2 VAC, 230V mode: 184±2 to 278±2 VAC

240V mode: 192±2 to 278±2 VAC, 100V mode: 160±2 to 288±2 VAC

Input voltage range

200V mode: 170±2 to 278±2 VAC, 208V mode: 177±2 to 278±2 VAC

220V mode: 186±2 to 278±2 VAC, 230V mode: 194±2 to 278±2 VAC

240V mode: 202±2 to 278±2 VAC, 100V mode: 170±2 to 278±2 VAC

Input frequency

50/60 Hz±1, 3, 5, or 14% (5% in the factory settings)

Maximum current (at rated voltage/

minimum input voltage)

9A/11A

14A/16A

23A/27A

Phase

Single-phase, two-wire (grounded)

Input plug

Terminal block

NEMA L6-30P / Terminal 

block

Input protection

NFB

Input protection capacity

16A

30A

AC output Output capacity (upper limit)

2000VA/1400W 

(1000 VA/700 W  

in 100V mode)

3000VA/2100W 

(1500 VA/1050 W  

in 100V mode)

5000VA/3500W 

(2500 VA/1750 W  

in 100V mode)

Rated current (output rating voltage)

10A

15A

25A

Switching time

Uninterrupted

Commercial direct shipment 

(switching time)

Uninterrupted

Output voltage (commercial operation)

200Vmode: AC200V±2%, 208Vmode: AC208±2%

220Vmode: AC220V±2%, 230Vmode: AC230±2%

240Vmode: AC240V±2%, 100Vmode: AC100V±5%

Output voltage (backup operation) 

200Vmode: AC200V±2%, 208Vmode: AC208±2% 

220Vmode: AC220V±2%, 230Vmode: AC230±2% 

240Vmode: AC240V±2%, 100Vmode: AC100V±5%

Output frequency (commercial 

operation)

Synchronized with input frequency

Output frequency (backup operation)

50/60Hz±0.5Hz

Output waveform (In Commercial 

Power Mode/Battery Mode)

Sine wave / Sine wave

Waveform distortion rate

7% max. (Rectified load, at rated output)

3% max. (Resistance load, at rated output)

Phase

Single-phase, two-wire

Output receptacles

Terminal block

NEMA L6-30R x 2, 

terminal block

Battery Sealed lead battery life expectancy

5 years (ultralong operating life) (ambient temperature 25°C)

Battery capacity (V/Ah) (x Quantity)

12 VDC/ 9 Ah (x 4)

12 VDC/ 9 Ah (x 6)

12 VDC/ 9 Ah (x 12)

Charging time

8 hours

Backup time (25°C, initial characteristics)

5 min. (1400 W)

5 min. (2100 W)

5 min. (3500 W)

Dimensions (W x D x H mm)

430 x 660 x 88 (2U)

430 x 700 x 132 (3U)

Weight of unit

Approx. 28kg

Approx. 33kg

Approx. 61kg

Operating environment temperature/humidity

0°C to 40°C, 25 to 85%RH with no condensation

Storage environment temperature/humidity

-15°C to 50°C, 10 to 90%RH 

(with battery fully charged, stored with no condensation)

Noise regulation

VCCI Class A compliant

Safety standard compliance

UL1778/CE/RoHS compliance

Internal power consumption (normal/maximum)

70W (*1)/145W (*2)

148W (*1)/265W (*2)

249W (*1)/480W (*2)

Noise

45 dB max.

50 dB max.

Cooling method

Forced air cooling

Serial communication (RS-232C) (interface) 

●(D-sub 9pin)

Contact signal (interface)

● (D-sub 9pin)

*1: Rated load/ Rated input voltage/ When fully charged

*2: Rated load/ Rated input voltage/ When battery charge current is at maximum

Содержание BU2002RWL















































































Отзывы: