background image

10

 

 

Replacement procedure 

With  the  power  supply  output  switch  ON  during  normal  operation  (inverter  output),  you  can  switch  to 
maintenance mode to perform replacement for the operations described below. 
(1) Press and hold the indicator selection switch (on the front panel of the UPS) for 10 seconds. 

Power supply output switch 

The status indicator shows ˝REP˝. 

 

The beep sounds. 

(2) The unit switches to bypass mode, enabling the battery unit to be replaced. 

 

Disconnect the connectors of all cables connected to the rear of the battery unit.

 

After replacing the battery unit, make sure to reconnect all of the disconnected cables.  

 

Make sure the battery unit’s built-in battery connector (in the front panel) is connected. 

 

If commercial power is supplied to the battery unit, make sure the ˝charging˝ indicator on the battery 

unit’s front panel is illuminated. 

 

(3) When you finish connecting the battery, press and hold the indicator selection switch (on the front panel 

of the UPS) for 10 seconds. 

 

Maintenance mode is released and the unit returns to normal inverter operation. 

 

The status indicator returns to its normal input voltage display (VI ***). 

 

 

Battery replacement is complete.

Caution: In this operating condition, the unit will not enter Battery Mode if a power failure occurs. 

Содержание BHM100PC













Отзывы: