manualshive.com logo in svg

OmniGuide BEACON 420030-AA, Инструкция по эксплуатации

Поделиться
Скачать
OmniGuide BEACON 420030-AA Скачать руководство пользователя страница 44

L-1670 Rev 0

44

© OmniGuide, Inc.

Functionality

The display screen, RfID antenna, articulating arm, wheels, emergency machine 

off, rear panel and foot switch are to be checked for routine functionality. The 

unit is to be inspected for any loose, missing or damaged hardware.

Parts

The BEACON Advanced Energy Laser System cart, and accessories are to be inspected for 

any loose, damaged, or missing parts. The following parts are to be replaced annually:

14.1.1 Fan filter element (located under the air intake enclosure panel 

on the right side of the laser), PN 1-0092-015-00-00

14.1.2 Yoke washers for the CGA-930 fitting that connects the inlet hoses for 

the gas management assembly to the tanks, PN 1-0090-017-00-00

OmniGuide Service

for additional information on the Yearly Preventive Maintenance please 

contact OmniGuide Service at 1-888-666-4484.

15.0 TROUBLESHOOTING

System does not start

1.  Check if electrical power cord is fully securely plugged into an individual outlet
2.  Check if electrical power cord is fully plugged into the Laser
3.  Check if mains switch at the laser base is in “ON“ position
4.  Check if emergency switch is pulled out all the way
5.  Check if the door interlock connector is in place at base of Laser
6.  Check fuses at the mains connector at base of the Laser. If the fuses are 

blown, exchange fuses with spare fuses supplied with the system.

7.  Door is interlocked, and the door is open.

If the problem persists, contact OmniGuide service for assistance (1-888-666-4484)

Password does not work

Retype the pin code (password). If you cannot get into the main menu, restart the system and retry. If you 

have no success entering the main menu contact OmniGuide service for assistance (1-888-666-4484).

No effect on tissue

1. 

Prior to surgery the laser is to be test fired to confirm the aiming beam and CO beam are aligned 

and that there is no clipping or observed disfigured beam if the articulating arm is to be used.

2.  Increase the power of the system
3.  Is the “Ready” button pressed?
4.  Increase the pulse length

Содержание BEACON 420030-AA
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды