background image

Open

16

17

BOWL DISASSEMBLY AND WASH

STERILIZATION AND EASY CLEANING SYSTEM

Juice cap 

packing

bowl packing

Extraction 

packing

1

Remove Juice Cap packing and bowl packing.

2

Open the extraction packing at 

the bottom of the bowl

3

Wash the bowl and all the packings.

   Wash bowl and bowl packing with cleaning 

brush under the running water.

   Open juice cap first. Hold the bowl and juice cap with one hand and remove juice cap packing with the other hand. 

When removing it, be careful not to drop the juice cap and bowl. It may cause damage to the juice cap. 

Remove the bowl packing by pinching and twisting it with two fingers.

1

After closing the juice cap, pour the water 

into feeding tube and operate the appliance.

For sterilization, use baking soda or natural wash-up liquids only.

2

After a while, open the juice cap 

and discharge the water.

   You can thoroughly wash parts by immersing in water diluted with one or two drops of baking soda 

or natural wash-up liquids for about 30 minutes.

   Whenever changing the ingredient, it is not necessary to disassemble and wash the bowl. 

After juicing, make sure to disassemble and wash the bowl set.

STERILIZATION

EASY CLEANING SYSTEM

Содержание VRT400 SERIES















Отзывы: