Omega PCL1200 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 60

Omega PCL1200 Скачать руководство пользователя страница 58

54

9. Maintenance

9.1 Replacing Batteries

Replace batteries as soon as the battery indicator turns on to avoid
false measurements. If the batteries discharge too deeply the
PCL1200 will automatically shut down to avoid battery leakage.
Note: Use only AA size alkaline batteries or optional rechargeable
batteries.

Warning

This product has non-rechargeable alkaline batteries installed.
Prior to connecting any AC adapter or battery charger, these
batteries must be removed and/or replaced with rechargeable
batteries such as Nickel Cadmium or Nickel Metal Hydride types.
Failure to remove the batteries will result in damage to the calibrator
and voids the warranty.

9.2 Cleaning the Unit

Warning

To avoid personal injury or damage to the calibrator, use only the
specified replacement parts and do not allow water into the case.

Caution

To avoid damaging the plastic lens and case, do not use solvents or
abrasive cleansers.
Clean the calibrator with a soft cloth dampened with water or water
and mild soap.

9.3 Service Center Calibration or Repair

Only qualified service personnel should perform calibration, repairs,
or servicing not covered in this manual. If the calibrator fails, check
the batteries first, and replace them if needed.
Verify that the calibrator is being operated as explained in this
manual. If the calibrator is faulty, contact OMEGA's customer service
department for an AR# before returning. Be sure to pack the
calibrator securely, using the original shipping container if it is
available.

«
...
56
57
58
59
60
»

Содержание PCL1200





























































Отзывы:

Нет отзывов