Omega PCL1200 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 60

Omega PCL1200 Скачать руководство пользователя страница 21

17

4.1 Setting 0% and 100% Output Parameters

To set the 0% and 100% points, use the following steps:
1. Select the lower display [LOWER] from Main Menu, and choose

the desired primary parameter.

2. Select output [OUT] from the input/output control, and enter the

desired value. For example select [VOLTS OUT].

3. Enter 5V with the keypad and press Enter.

4. Press any one of the four cursor control arrows to display the

setpoint control menu.

5. Hold down the Function Key that corresponds to 0% [F1]. 0%

will flash and the setpoint is stored.

6. Repeat these steps, entering 20V and holding the Function Key

that corresponds to 100% [F3].

7. Use the 25% key to cycle 5 V and 20 V in 25% increments.

4.1-1 Stepping the current output

To use the 25% function with mA output, follow these steps:

1.

Select the lower display from the Main Menu, and choose
mA.

2.

Use the 25% key to cycle between 4 mA and 20 mA in 25
% intervals.

4.2 Using the Automatic Output Functions

There are two automatic output functions, step and ramp. The
selected function can be turned on and off using the Output Home

Menu. The Automatic Output Function parameters can be set in the
Auto Function Menu.

Parameters include:

1. Which auto function will be available (Step or Ramp).
2. The Auto Function Time, time between steps for step and time to

get from over one limit to the next for ramp.

The limits for the ramp and step functions are set to the 0% and
100% values. See Section 4.1 Setting 0% and 100% Output
Parameters. Steps are in 25% increments from the 0% value to the
100% value.

4.3 Sourcing mA

To source a current, follow these steps:

1. From the Main Menu select lower display [LOWER]. Choose

[mA] from the primary parameters.

«
...
19
20
21
22
23
...
»

Содержание PCL1200





























































Отзывы:

Нет отзывов