![background image](http://html1.mh-extra.com/html/omega/omp-modl/omp-modl_user-manual_4017938038.webp)
3... I
NTERFACE
M
ODULES
U
SING
T
HE
OMP-MODL
3-14
Memory and Continue Processing
during setup of the
Program Net within HyperNet (Global Icon option).
M
EM
F
ULL
W
RAPPING
Displays when the OMP-MODL Program Net is configured in
the Rotary Memory mode. When memory fills, the OMP-
MODL starts writing over the first collected data. Since the
Program Net is still executing, alarms and control functions
continue to be monitored. Rotary Memory mode is enabled
during setup of the Program Net under the Global Icon.
R
CV
’
ING
N
ET
Displays momentarily during the actual serial upload of of a
Program Net to the OMP-MODL.
N
O
P
ROGRAM
N
ET
Displays upon first power up of the OMP-MODL after the
Program Net has been lost. This should only occur after
replacement (or initial installation) of the lithium cell used for
Data Memory backup. The display indicates that a search
for a valid Program Net stored within the OMP-MODL
memory has failed.
In the event that this message displays, check (and replace
if low) the Lithium Cell via the STATUS menu described
below. Then reprogram the OMP-MODL with a new
Program Net.
B
AD
P
ROGRAM
N
ET
Displays if an illegal or corrupted Program Net is in memory.
This message should only occur if memory containing the
Program Net has been corrupted or the unit has undergone
a 3-button Initialization which has cleared out the OMP-
MODL Program Net. In the event that this message
displays, reprogram the logger with a new Program Net,
then check (and replace if low) the Lithium Cell via the
STATUS menu described below.
C
ARD
E
RROR
: M
ISSING
F
ILE
Displays upon power-up of the OMP-MODL with an
improperly prepared PCMCIA card inserted (MLIM-5
module). The card should be formatted and prepared for
use within the OMP-MODL as described in Chapter 6.
B
AD
C
ONFIG
Displays if User selectable switch settings on the MLAD-1 or
any other OMP-MODL Interface Modules do not match the
currently loaded Program Net. The message also identifies
which Interface Module and channel or incompatible. If this
message displays, modify the Program Net to match the
hardware or open the OMP-MODL and examine the switch
settings on the installed Interface Modules and correct the
invalid setting(s).
S
YSTEM
S
TATUS
From the Top Menu, pressing the Next button once will advance
the display to System Status. Pressing SELECT while System
Содержание OMP-MODL
