![background image](http://html1.mh-extra.com/html/omega/omp-modl/omp-modl_user-manual_4017938189.webp)
11.. . A
PPENDIX
A: M
ASTER
I
CON
R
EFERENCE
U
SING THE
OMP-MODL
11-27
FREQUENCY
I
NPUT
I
CON
(D
IGITAL
I/O
WITH
MLIM-2)
FUNCTION:
Event / Counter / Frequency input and Digital output functions are all provided with the
MLIM-2. With the MLIM-2 installed in a OMP-MODL, these respective function icons
become available for use in Program Nets.
The same dialog is used to configure the channel for Event, Frequency, and Counter
functions.
As a FREQUENCY input, the MLIM-2 channel samples the incoming waveform and
outputs the measured frequency to the net.
Calculation of the input signal frequency requires longer for lower frequencies. Due to
this effect, the speed of execution of a Program Net may be reduced when reading low
frequency inputs. (eg 10Hz inputs will require approximately 100mS to read, whereas a
100Hz input will require only 10mS)
NOTE: Due to the advanced signal processing utilized in the frequency mode,
unbalanced duty-cycle inputs are measured with the same accuracy as balanced duty-
cycle inputs.
INPUTS:
Hardware:
No signal input shown on Net for Program Net connections.
Update:
The measured frequency is output every time an Update command is
received on the Update input.
Enable:
Processing of the icon is allowed when Enable pin is unconnected or
connected
and
the Enable signal is TRUE.
OUTPUTS:
Output Signal:
Data type signal, Frequency in Hz.
ICON CONFIGURATION DIALOG BOX:
CONFIGURATION OPTIONS:
Icon Name:
Specify the name for the channel. This name will show directly under the
icon within the Program Net. If no name is User provided, the Backplane
Port (1 to 6) and Channel (A to D) where the actual Interface Module
channel is installed will be used for the name.
Output Name:
Specify a name for the Output signal from this icon. This Output
Name will be referenced by other icons downstream in the Program Net.
Содержание OMP-MODL
