1
Selectable
Coded
Override
1 & 0 (see page 29)
2
Last Door Arming
O
F
F
3
Automatic Rearming
O
F
F
4
Starter Interrupt Circuit
O
N
5
Automatic Starter Interrupt
O
F
F
6
Ignition Activated Override
O
F
F
7
Doors Lock With Last Door Arming
O
F
F
8
Doors Lock With Automatic Rearming
O
F
F
9
Doors Lock With Ignition
O
N
10
Ignition OFF Unlock #1
ON
11
Ignition OFF Unlock #2
ON
12
Open Door Bypass T
o Previous Three Features
ON
13
Confirmation Chirps
O
N
14
Confirmation Chirps In V
alet Mode
O
F
F
15
Activated
Alarm
Cycle
6
0
Seconds (LOCK)
16
Lights
On
Upon
Disarm
O
N
(LOCK)
17
Disarm Alarm Upon Trunk Release
ON
18
Doorlock
Pulse
Time
.
8
second (LOCK)
19
Double Unlock Pulse
O
F
F
20
Arming
Delay
3 Seconds (LOCK)
21
Pulsed
Horn
/ Steady
Siren
Output
Pulsed Horn ( LOCK)
22
Loud or Soft Confirmation Chirps
Loud
(LOCK)
23
Total Closure Lock Output
O
F
F
24
Alarm Functions Bypass
O
F
F
25
Ignition-Activated Anti-Carjacking Protection
O
F
F
26
Door-Activated Anti-Carjacking Protection
O
F
F
27
Open Door Warning Upon Arming
OFF
28
P
ANIC Button Operates "Panic" or Additional Output Panic (LOCK)
29
Transmitter-Activated Anti-Carjacking Protection
O
F
F
#
FEA
TURE
D
E
F
A
U
L
T
Step 1 -
Turn the ignition "off", and press the valet switch 5 times.
(the system will respond by briefly sounding the horn)
Step 2 -
Press the valet switch the same number of times as the
feature number.
(the system will acknowledge the valet switch entry by
repeating the same number of chirps)
Step 3 -
Press the transmitter's LOCK button to turn the feature
"on", or press the UNLOCK button to turn the feature "off".
(turning the feature "on" is indicated by one horn chirp;
turning the feature "off" is indicated by two horn chirps)
Repeat - Steps 2 and 3 for each feature to be changed
This checklist helps when programming features. Before
attempting feature programming, please carefully read pages 29-
39 to become familiar with the features and the programming
procedure. Mark each applicable box with "\" next to the feature
to be changed before entering Features Programming Mode. As
each feature is programmed, change its mark to "X".
Features Programming Checklist
Page - 22
Your Executive Model One system features a port which allows an optional
auxiliary shock sensor to easily be added to increase the effectiveness of your system
when it is armed. A light shock or impact to the vehicle will produce a "Prewarn",
which chirps the horn and locks the doors. A heavier shock or impact will fully activate
the security system. Other sensors are available which include those that detect
changes in atmospheric pressure within the vehicle, and radar proximity sensors that
can detect moving objects inside and outside the vehicle. If the system does include
a sensor, it may be temporarily bypassed when arming by pressing the OPTION
button within 5 seconds after pressing the LOCK button to arm the system. If the
system is activated by the optional sensor, the Zone Violation feature will flash the LED
status light four times between pauses; Prewarn activation has no indication.
Shock Sensor Port with Prewarn
Each remote transmitter has as part of its operation a unique digital code which
identifies it as an authorized controller to the processor within the Executive Model
One unit. Your Model One system is capable of being operated by up to four different
remote transmitters, which must be programmed to operate the system. The process
of programming additional transmitters is relatively easy, creating an inherent
weakness shared by virtually every remote controlled device. Your Model One
Programming Transmitters
system, however, has patented technology, Automatic Transmitter Verification
TM,
which eliminates this weakness.
In normal daily operation, every time the ignition switch is turned "on", the LED
status light indicates how many remote transmitters are capable of operating your
system. For example: two flashes and a pause indicate that only two transmitters are
coded to operate your system; this display occurs for a period of 10 seconds every
time the ignition switch is turned "on".
48 hours after installation, or transmitter programming activity, the audible and
visual Unauthorized Transmitter Alert will revert to the 10 second visual display
upon turning the ignition switch "on".
In the event the system alerts you to a recent transmitter addition, you should
immediately reprogram your transmitters to the system, which will effectively erase
any unauthorized transmitters.
Note: For the first 48 hours after transmitters are coded, every
time the ignition switch is turned "on", the horn will chirp
rapidly for two seconds and the LED status light will flash the
number of transmitters between pauses for 90 seconds. This is
the "Unauthorized Transmitter Alert".
Page - 23
