Using a simple programming process, extra or replacement transmitters are easily
added to your security system. To access the Transmitter Programming Mode,
follow this procedure:
Step 1 -
Turn the ignition "on". Within 7 seconds , press the valet switch 5 times.
The system will respond by briefly sounding the horn once.
Step 2 -
Now press the LOCK button on each transmitter to programmed. The
system will respond to each with a horn chirp, which confirms that the transmitter
has been programmed into the system.
Repeat Step 2 for each transmitter which is to operate the system. The system
can be operated by up to four transmitters. Please note that when any transmitter is
programmed, even one which already operates the system, all previously known
transmitter's codes will be erased as a security measure. Therefore, when program-
ming an additional or replacement transmitter into the system, all of the transmitters
which are to operate the system must be programmed at the same time.
Turning the ignition switch "off", or 15 seconds of no programming activity, will
cause the system to exit the Transmitter Programming Mode, which the system will
indicate by briefly sounding the horn. If programming the maximum being four
transmitters, when the fourth transmitter is acknowledged, the system will automati-
cally exit Transmitter Programming Mode.
Page - 24
Page - 25
Your Executive Model One vehicle security system has 29 features which may be
programmed to suit your needs via the Features Programming Mode. This is
accessed by turning the ignition switch "off" and pressing the valet switch five times.
Once in Features Programming Mode, the valet switch is further used to specify which
of the 29 features is to be changed, then the transmitter is used to change the selected
feature's setting.
To access the Features Programming Mode, follow these steps:
Step 1 - Within 5 seconds of turning the ignition "off", momentarily press the valet
switch 5 times. The system will respond by chirping, then briefly sounding the horn,
and the LED status light will start rapidly flashing.
Step 2 - You now have 10 seconds in which access the desired feature. This done
by pressing the valet switch the number of times that equal to feature number. For
example, to utilize the optional siren, the audible output must be changed from
pulsed to steady. This is the twenty-first feature on the list, and therefore to
access it, you must press the valet switch 21 times. The system will acknowledge
the valet switch entry by chirping the horn a like number of times equal to the
valet switch presses; in this case 21 chirps will indicate access to the twenty-first
Programming Features
Page - 26
feature. When the feature is selected, the LED status light will change from rapidly
flashing to flashing the same number as the feature, between pauses.
Step 3 - You have 10 seconds to change the chosen feature. Press the transmitter's
LOCK button to turn the feature "on", or press the UNLOCK button to turn the
feature "off". Turning the feature "on" is indicated by one horn chirp; turning the
feature "off" is indicated by two horn chirps. Also, turning a feature "on" will cause
the LED status light to illuminate steady, while turning the feature "off" will cause
the LED status light to go out.
Once a particular feature has been configured to the desired setting, the next
feature to be programmed may be accessed by repeating Step 2; i.e. press the valet
switch equal to the number of the next feature. As each is programmed, proceed to
access each in turn for programming until finished.
If 10 seconds expire without programming activity (i.e.- not pressing the LOCK or
UNLOCK buttons or pressing the valet switch to select another feature), the system
will exit the Features Programming Mode, which is indicated by the horn sounding
once.
The 29 Programmable Features, their factory-set default settings, and the
transmitter button which equals the default setting are as follows:
#1
Selectable Coded Override: Default 1 & 0 (see pages 29-30).
#2
Last Door Arming: Default OFF (UNLOCK).
#3
90 Second Automatic Rearming: Default OFF (UNLOCK).
#4
Starter Interrupt Circuit: Default ON (LOCK).
#5
90 Second No Ignition Starter Interrupt: Default OFF (UNLOCK).
#6
Ignition Activated Override: Default OFF (UNLOCK).
#7
Doors Lock With Last Door Arming: Default OFF (UNLOCK).
#8
Doors Lock With 90 Second Automatic Rearming: Default OFF (UNLOCK).
#9
Doors Lock With Ignition: Default ON (LOCK).
#10 Ignition OFF Unlock #1: Default ON (LOCK).
#11 Ignition OFF Unlock #2: Default ON (LOCK).
#12 Open Door Bypass To Previous Three Features: Default ON (LOCK).
#13 Confirmation Chirps: Default ON (LOCK).
#14 Confirmation Chirps In Valet Mode: Default OFF (UNLOCK).
#15 Activated Alarm Cycle: Default 60 Seconds (LOCK).
Page - 27
