background image

Outdoor Living Today 

Flower Box Assembly Instructions 

2. 

Position Front Frame Piece flush with End Cap. Attach both ends with 2 - 1 1/4” screws. Pilot hole Rear 

Box Frame near bottom center and secure to Base edge with 1 - 1 1/4” screw.  Evenly position Front Trim 
(mitre cut on end and dado cut on inside bottom) tight against front frame and nail down with 4 - 1 1/4” nails.  
Position Side Trims as per Front and secure with 3 - 1 1/4” nails per side.

1. 

On a table position Rear Box and End Cap Frames together so flush at top.  Fasten together with  

2 - 1 1/4” screws. Place Base Frame tight against Rear and End Cap and flush at bottom.  Secure with  
2 - 1 1/4” screws. Complete attachment of remaining End Cap Frame. Slide Front Frame between End Caps.

3. 

On a flat surface, flip Flower Box on it’s rear face.  Evenly space Brackets and secure through Base Frame 

and into the Brackets with  2 - 1 1/4” screws per Bracket.  Position completed Flower Box beneath window trim 
and screw from inside of box into the center wall stud with 2 - 2” screws. (2” screws supplied with Base Kit.)

Parts Lists:

            

 

 

A - Base, Rear & Front Box Frames  (3pcs) 

 3/4” x 5 1/2” x 23” 

B - End Cap Frames 

    (2pcs) 

 3/4” x 5 1/2” x 7” / 8”

 

C - Front Trim 

    (1 pc)  

3/4” x 1 1/2” x 26” 

D - Side Trims 

    (2 pc)  

3/4” x 1 1/2” x 8 3/4” 

E - Brackets 

    (2 pc)  

1 1/2” x 5 1/2” x 5 1/2” 

F - 1 1/4” Screws

 

G - 1 1/4” Nails

Rear (A)

Front (A)

Base (A)

End Caps (B)

Front Trim (C)

Side Trims (D)

Brackets (E)

1 1/4” 
Screws (F)

1 1/4” 
Nails (G)

Rear (A)

Right Angle Cut to Rear

Flush

Base (A)

Front (A)

End Cap

Front

Flush

Front Trim

Side Trim

Rear

1 1/4” screws

Flush

2” screws

Exploded 

View

1 1/4” Screw

Rear (A)

1 1/4” 
Nails

  Toll Free 1-888-658-1658              www.outdoorlivingtoday.com        [email protected]

Page 35

Содержание GS84-S





































Отзывы: