Outdoor Living Today www.outdoorlivingtoday.com [email protected]
Page 4
Thank you for purchasing our 6x3 Garden Saver.
Please take the time to identify all the parts prior to assembly.
Note: Trim and Skirting pieces are graded with the best face being rough sawn.
Rough sawn cedar is much easier to paint and stain.
Parts List
A. - Floor Section
Floors
1 - Floor Section - 35” x 73”
1 - Mid Floor Joist - 1 1/2” x 2 1/2” x 70”
Steps
1
B. - Wall Section
Main Wall Panels
4 - Rear/Side Walls - 35” x 63 1/4” - Identical
4 - Top Wall Plates - 1 1/2” x 1 1/2” x 35”
2 - Front Narrow Walls - 12 1/2” x 61 3/4” - Identical
Header/Wall Extenders
1 - Front Header - 1 1/2” x 1 1/2” x 70”
1 - Interior Door Header - 1 1/2” x 1 1/2” x 44 7/8”
2 - Left/Right Side Angle Gables - 6 1/2” x 35”
2 - Wall Extenders - 6 1/4” x 35”
1 - Rear Top Plate - 1 1/2” x 1 1/2” x 70”
Shelves
Storage Shelf Supports
Short (2 - 3/4” x 2 1/2” x 12 1/2”)
Long (2 - 3/4” x 2 1/2” x 35”)
2 - Storage Shelves - 11 1/2” x 31 7/8”
2 - 11
12 - 23
24 - 25
C. - Roof Section
Roof
3 - Metal Roof Panels - 39” Length
3 - Battens - 3/4” x 3 1/2” 74 1/4”
4 - Batten Spacers - 3/4” x 1 1/2” x 12 3/8”
6 - Foam Enclosures
26 - 34
D. - Trim / Misc. Section
Lower Skirting
2 - Lower Rear Skirting - 1/2” x 2 1/2” x 35”
2 - Lower Side Skirting - 1/2” x 2 1/2” x 33”
Lower Front Skirting
Short (2 - 1/2” x 2 1/2” x 11 1/8”)
Long (1 - 1/2” x 2 1/2” x 47 1/4”)
Filler Trim
8 - Front/Rear Filler Trims - 5/8” x 1 1/2” x 30”
1 - Front Header Filler Strip - 5/8” x 1” x 69 1/2”
1 - Rear Top Plate Filler Strip - 5/8” x 1 1/2” x 69 1/2”
36
37 - 40
D. - Trim / Misc. Section Cont.
Outer Wall Trim and Fascia
1 - Upper Front Horizontal Trim - 1/2” x 2 1/2” x 74 1/4”
2 - Side Fascia Trims - 1/2” x 2 1/2” x 37 5/8” - Angle Cut
Ends
2 - Front Wide Corner Trims - 1/2” x 3 1/2” x 70 3/8”
2 - Front Side Corner Trims - 1/2” x 2 1/2” x 70 3/8” - Angle
Cut End
2 - Rear Wide Corner Trims - 1/2” x 3 1/2” x 67 3/4”
2 - Rear Side Corner Trims - 1/2” x 2 1/2” x 65 1/2” - Angle
Cut End
1 - Upper Rear Horizontal Trim - 1/2” x 2 1/2” x 67 1/4”
1 - Rear Center Trim - 1/2” x 2 1/2” x 65 1/8”
2 - Vertical Door Frame Trim - 1/2” x 2 1/2” x 64 1/4”
Door System
1 - Door Threshold (Bevel) - 1/2” x 2 5/8” x 44 7/8”
2 - Left/Right Doors - 22 1/4” x 61 3/8”
1 - Door Flange - 1/2” x 2 1/2” x 61 3/8”
4 - Vertical Interior Door Stops - 3/4” x 3/4” x 29 7/8”
Miscellaneous
1 - Front Horizontal Trim - 1/2” x 3” x 67 1/4”
1 - Metal Drip Edge - 60”
1 - Front Middle Trim - 1/2” x 2 1/2” x 2 5/8"
2 - Metal Peak Cap - 60”
1 - Metal Roof Edge Trim (96”)
** Plus 2 Cedar Shingle Shims - discard after shimming
doors
Steps
41 - 48
49 - 61
62 - 65
Note: We recommend you drill a 1/8” pilot hole for each
screw to avoid splitting wood. The hole depth should be
equal to 3/4 the length of screw.