Olivetti IC-420 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 61

Olivetti IC-420 Скачать руководство пользователя страница 56

54

Service Guide: Fiery® ES IC-420

Troubleshooting

Printing to the Fiery ES

If the customer can print the Fiery ES Test Page but cannot print a job from a computer on the network, you may have to
make a service call. However, first make sure that the site administrator has done the following:

•

Checked all components of the network, including cables, connectors, terminators, network adapter boards, and
network drivers.

•

Activated the network and used it to communicate with other printers.

•

Confirmed that the applicable network settings in Setup (such as AppleTalk zone, IP address, subnet mask, and
gateway address) match the settings used in the network.

When you make a service call, check the Fiery ES connector panel to make sure that the appropriate network connection is
in place. Print quality problems are difficult to trace. Before you try to troubleshoot print quality problems, print a Test
Page to make sure that the printer does not need servicing or adjusting. Also, make sure that the correct paper is being used
in the printer.

Note:

EPS file generation is not completely standardized among applications. Some users may encounter problems while

printing certain EPS files.

If the printer does not print

The following table lists possible causes and solutions when the printer does not print.

Table 2:

Causes and solutions when printer does not print

Possible Cause

Solution

Is the power on?

•

Turn on the Fiery ES using the power button and the printer power switch.

Are the cables between the
Fiery ES and the printer
connected?

•

Make sure that the printer interface cables are completely and correctly connected to the
printer and the Fiery ES.

Is the specified paper loaded?

•

Load the specified paper in any of the input trays.

Can you print a Test Page from
the printer driver?

•

If you cannot print the Test Page, the printer may be out of order. You may need to service the
printer.

Is the enclosed fan present and
functioning?

•

Verify that the enclosed fan is present, oriented correctly, and functioning (see

Service Guide

Y119660-9

«
...
54
55
56
57
58
...
»

Содержание IC-420






























































Отзывы:

Нет отзывов