Olivetti d-Color MF220 Скачать руководство пользователя страница 77

Страница: 77 / 315

d-Color MF360/280/220 (Version 3)

5-13

5.1

[Basic]

[Offset] [Yes]/[No]

Specify whether to separate each set of copies from another set in the output
tray when copying multiple sets of multi-page originals.

When the

Finisher FS-527

Finisher FS-529

, or

Job Separator JS-505

is not

installed:
If the following conditions are met, printed copies are fed out and sorted in an
alternating crisscross pattern.
•

The 8-1/2

11, A4, or B5 size paper is used

•

Paper of the same size and type is loaded with the

orientation in one pa-

per tray and with the

orientation in another tray

•

Auto paper selection is specified for the paper size setting

When the

Finisher FS-527

Finisher FS-529

, or

Job Separator JS-505

is in-

stalled:
The copies are fed out and stacked on top of each other with each set shifted
to separate it.

[Fold/Bind]

Staples copy outputs in the center the paper or fold them in the center before
discharging.

[Half-Fold]

[Center Staple & Fold]

[Staple]

Staples copies in corner or at two points before they are output.

[Punch]

Punches holes in copies before they are output.

[Position Setting]

Configure desired staple or hole-punch positions.

Select Auto, and the machine automatically judges the staple or punch posi-
tions for the paper relative to the original direction loaded.
•

A staple or punch position along the long side of the paper is selected if the
original length is 11-11/16 inches (297 mm) or less.

•

A staple or punch position along the short side of the paper is selected if
the original length exceeds 11-11/16 inches (297 mm).

•

Staple or punching positions are set on the upper or left-side end.

•

Be sure to load the original so that its top side is placed in the back.

•

If desired, press [Original Direction], and then select the original direction.

Settings

Содержание d-Color MF220




























































































































































































































































































































Результаты поиска

Содержание d-Color MF220

Отзывы:

Похожие инструкции для d-Color MF220

Бренды по названию

Популярные бренды

Olivetti d-Color MF220, Копирование операций

Результаты поиска

Содержание d-Color MF220

Отзывы:

Похожие инструкции для d-Color MF220

Бренды по названию

Популярные бренды