Oki C301 Скачать руководство пользователя страница 152 | Manualshive

Страница: 152 / 218

background image

44951501TH Rev.2

7-27

Oki Data CONFIDENTIAL

7. TROUBLESHOOTING

Check item

Check operation

Actions for NG

results

(2-1-3) Connection-line check

Operator panel

connection

Check the same as (1-1).
The printer does not operate unless the
operator panel is detected and operated.

Follow (1-1).

(2-2) Abnormal sound is heard

Check item

Check operation

Actions for NG

results

(2-2-1) Motor step losing check (driver problem)

Each motor’s

operation

By using the self-diagnostic mode, check

each motor for proper operation by whether

the motor is loaded or not. The motor beeps

when improper.

Replace the

CU/PU board.

Motor cords

Check the wiring for each motor as follows:

Visually check for, or check for with a tester,

short circuiting.

Remove the motor cord from the board side,

and the resistance between each pin on the

side of the cord and the frame ground.

Replace the

motor cord.

Re-assemble

parts properly.

(2-2-2) Motor step losing check (consumable load problem)

Operating conditions
of the respective
motors

Check if operations of the respective motors are
normal or not by using the self-diagnostic mode.
Check if any load exists or not.
"Buzzer" sound when an error occurs.

Replace the
corresponding
consumable
item.
If any attempt
of using new
part as a trial
is going to
be made, be
sure to use
the System
Maintenance
Menu FUSE
KEEP MODE.

Check item

Check operation

Actions for NG

results

(2-2-3) Gear tooth disengagement check (consumable load problem)

Operating conditions
of the respective
motors

Check if operations of the respective motors are
normal or not by using the self-diagnostic mode.
Check if any load exists or not.
"Buzz buzz" sound is generated when an error
occurs.

Replace the
corresponding
consumable
item.
If any attempt
of using new
part as a trial
is going to
be made, be
sure to use
the System
Maintenance
Menu FUSE
KEEP MODE.

Installation condition
of each consumable
item

Check by visual inspection if the respective
consumable items are installed in their normal
positions in which gears of the consumable
items engage accurately or not.

Replace an
appropriate
mechanical part
as required, or
adjust or repair

(2-2-4) Cord routing check

Check the
installation
conditions of the
partition plate under
the CU and PU
boards.

Remove the CU and PU board, and inspect the
installation conditions of the partition plate by
visual inspection.

If they are not
hooked on the
normal specified
positions,
correct them.

«
...
150
151
152
153
154
...
»

Содержание C301



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для C301

Бренд: QMS Страницы: 122

Бренд: QMS Страницы: 306

Бренд: Oki Страницы: 24

Бренд: VAF instruments Страницы: 24

Magicolor 2 plus

Бренд: QMS Страницы: 90

Magicolor 2 Desklaser

Бренд: QMS Страницы: 4

Бренд: QMS Страницы: 8

Бренд: QMS Страницы: 94

Бренд: QMS Страницы: 6

Бренд: Cashino Страницы: 74

Бренд: Ricoh Страницы: 236

Бренд: Kyocera Страницы: 410

imagePRESS V1000

Бренд: Canon Страницы: 123

8560/SDN - Phaser Color Solid Ink Printer

Бренд: Xerox Страницы: 16

Бренд: KOMDRUCK Страницы: 8

Бренд: Muton Страницы: 16

Бренд: Matan Страницы: 8

Бренд: Panasonic Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды