Oki C301 Скачать руководство пользователя страница 148

Страница: 148 / 218

44951501TH Rev.2

7-23

Oki Data CONFIDENTIAL

7. TROUBLESHOOTING

Display

Causes

Error detail

Actions

POWER OFF/ON

901:ERROR

904:ERROR

Belt

temperature

error

901: Short

circuit

902: Open

circuit

903: High

temperature

904: Low

temperature

Is the cable from the belt

thermistor to the CU/PU

board connected properly?

Does the error occur again?

Yes

Connect the cable

properly.

Turn off and on

the printer.

Replace the belt

thermistor.

POWER OFF/ON

923:ERROR

A lock error

with black

image drum

The image drum does not

revolve properly.

Does the error display is

provided again by turning off

and on the printer?

Yes

Be sure the image

drum is properly

installed properly.

Replace the

image drum unit.

Replace the

image drum

motor.

POWER OFF/ON

928:ERROR

Fuser motor

lock error

The fuser does not operate

properly?

Does the error occur again?

Yes

Check that the

fuser is properly

installed.

Replace the fuser.

Replace the fuser

motor.

POWER OFF/ON

933:ERROR

A clock error

correction

error with an

option unit

(which does

not occur with

the printer in

the factory

shipped

configuration)

Does the error occur again?

Yes

Be sure of

connector

contacts.

Replace the

option unit.

Display

Causes

Error detail

Actions

POWER OFF/ON
933:ERROR

Tray-2
CPU clock
frequency
error

SERVICE CALL
980:ERROR

Media
jamming error
around fuser

Media is jammed by
entangling around the fuser.

Turn off the
printer.
Replace the fuser.

SERVICE CALL
983:ERROR

Duplicate
toner cartridge
detection error

Multiple toner cartridges for
the same color ware detected.

Install toner
cartridges for
specified colors
at the proper
positions.

SERVICE CALL
990:ERROR

Waste toner
sensor
detection
error

Is the K toner cartridge
installed?
Does the error occur again?

Yes

Install the K toner
cartridge.
Be sure of cable
connection,
and then
perform board
replacement.

xxxxxxxxxxxxxxxx
CRC CHECK NG ( )

PU download
data CRC
check error

A CRC check error was
detected after downloading
of PU data (PU firmware and
custom media data).

Turn off and on
the printer, and
then re-download
it (In general use
of the printer, the
downloading is
not performed
and this error
does not occur).

WDT ERROR
ADR=××××××××

PU firmware
runaway

Does the error occur again?

Yes

Turn off and on
the printer.
Replace the CU/
PU board.

COMMUNICATION
ERROR

PU-CU
interface error

Does the error occur again?

Yes Replace the CU/

PU board.

Note!

With the printer’s temperature not more than 0ºC, Service call errors 188

Error, 171 Error, 175 Error, 903 Error and 904 Error may occur. After turn off

the printer, turn on the printer after the printer warms.

Содержание C301



























































































































































































































Результаты поиска

Содержание C301

Отзывы:

Похожие инструкции для C301

Бренды по названию

Популярные бренды

Oki C301, Руководство по обслуживанию

Результаты поиска

Содержание C301

Отзывы:

Похожие инструкции для C301

Бренды по названию

Популярные бренды