background image

– 4 –

Caution

Caution

Caution

Caution

Caution

Caution

Caution

AC Adapter

Do not use any AC adapter other than the one that is supplied with the product.

Rail

Do not scratch the rail.  Do not apply fats and oils to the rail.

Kinds of Screws That Must Not Be used

Do not use screws of any nonstandard mark or screws with fats and oils or dust adhering to their surfaces.

Precaution in Unloading Screws

Do not give undue force or impact to screws when unloading them.

Foreign Matters

Do not insert fingertips or foreign matters into the scoop chamber, clearance and hole while the feeder is in
operation.  You might suffer physical injury.
Do not put any screws other than those used and foreign matters into the feeder.

Unusual Operating Noises

If unusual noises are heard from the feeder while it is in operation, turn off the power switch and disconnect
the AC adapter from the plug outlet.
If you continue using the feeder without correcting the unusual noises, fires, electrical shocks or physical injury
could result.

Do Not Repair, Overhaul or Tamper the Feeder

Please consult your dealer for repair services.

Содержание FM-36 Series



























Отзывы:

Похожие инструкции для FM-36 Series