Oerlikon Leybold Vacuum 129 78 Скачать руководство пользователя

Страница: 20 / 32

3.5

Installing the Flexible Pressure Lines

Use flexlines from Oerlikon Leybold Vacuum only.

Replace any damaged flexlines.

Working instructions for self-sealing screw fittings

The interconnecting cables and elements possess self-sealing screw fittings.
The connections can be opened and closed without helium escaping.

Remove the protective caps from the screw fittings.

Keep the protective caps in a safe place.

Check all connections for dust and dirt particles and clean them as
necessary using a clean, lint-free cloth or a soft, clean brush.

Do not use solvents to clean the connections! The connections must not be
greased or oiled.

Check the correct fit of the flat gaskets in the screwed fittings with external
thread. Replace missing or damaged gaskets.

To mount the pressure lines, only use the supplied fork wrenches or fork
wrenches approved by Oerlikon Leybold Vacuum.

Only connect or disconnect pressure lines if the compressor unit is turned off
and the pressure is below 28 bar.

Do not twist the pressure lines.

When fixing the screw fittings, use one wrench for tightening and a second
wrench for countering; see Figs. 5 and 6.

Installation

GA12119_002_A3 - 01/2012 - © Oerlikon Leybold Vacuum

CAUTION

Stabilizing wrench

Wrench for tightening

Fig. 5 Mounting the self-sealing couplings

Содержание 129 78

































Результаты поиска

Содержание 129 78

Отзывы:

Похожие инструкции для 129 78

Бренды по названию

Популярные бренды

Oerlikon Leybold Vacuum 129 78, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 129 78

Отзывы:

Похожие инструкции для 129 78

Бренды по названию

Популярные бренды