background image

16

Problem

Solution

Air conditioner turns 

on and off rapidly

Noises coming from 

the unit when cooling

- A dirty air filter may be obstructing the cool air. Clean the filter as 

  instructed on the ‘CARE AND CLEANING SECTION’ of this manual.

- In cases where the outside temperature may be extremely high, set 

  the FAN speed to a higher setting to circulate the air cool air better.
- This may be the operating sound of air movement and is normal. 

  However, if the noise seems too loud, set the FAN to a lower speed 

  setting.

- The noise may be due to window vibration. This can happen when 

  the air conditioner is installed incorrectly. Refer to the installation 

  instruction on page 10 or check with the person who installed the 

  unit initially.

Water dripping 

INDOORS when the 

unit is on COOL

- The air conditioner may have been improperly installed. Tilt the air 

conditioner slightly outward to allow water to drain out. Refer to 

installation instructions on page 10 or check with the person who 

installed the unit initially.

Water dripping 

OUTSIDE when 

unit is cooling

- The unit may be accumulating a large quantity of moisture as it is 

  dehumidifying a humid room. This is normal operation for excessively 

  humid weather.

- Remote control may not be within range of the unit. Be sure to have 

  the remote control within a 20 foot radius in front of the unit.

- The remote control signal may be obstructed. Remove any obstructions 

  interfering with signal.

Room is too cold

- The temperature setting may be too low. Increase the temperature to 

  a more comfortable level.

Remote control 

'FOLLOW ME' mode 

deactivates prematurely 
(on some models only)

Содержание OBZ-06CR




















Отзывы: