Oce VarioPrint 6000 Plus Line Скачать руководство пользователя страница 65

Страница: 65 / 102

Lock the OPC unit (left)

Procedure

Rotate the metal OPC pulley until the end of the back side of the OPC belt runs near (+/- 0.1 inch)
the arrows of the yellow registration board.

[77] Reposition the OPC belt

Use the red handle to push the OPC unit inwards as far as possible.

[78] Move the OPC unit in

Use the service key to turn L5 counter-clockwise into the locked position.

Use the service key to turn L4 clockwise into the locked position.

Use the service key to turn L3 clockwise into the locked position.

Use the service key to turn L2 clockwise into the locked position.

Use the service key to turn L1 clockwise into the locked position.

[79] Lock the OPC unit

Lock the OPC unit (left)

Chapter 3 - Maintenance tasks - Level 2

Océ VarioPrint 6000 line

Содержание VarioPrint 6000 Plus Line







































































































Результаты поиска

Содержание VarioPrint 6000 Plus Line

Отзывы:

Похожие инструкции для VarioPrint 6000 Plus Line

Бренды по названию

Популярные бренды

Oce VarioPrint 6000 Plus Line, Руководство по обслуживанию

Результаты поиска

Содержание VarioPrint 6000 Plus Line

Отзывы:

Похожие инструкции для VarioPrint 6000 Plus Line

Бренды по названию

Популярные бренды