background image

A8814  Acq 

 

Page 11 

Connecting Third Party Modbus Devices 

Step 4

 (optional) - Connect the Modbus network loop as shown in the wiring diagram.  Follow the 

manufacturer’s instructions for installing and powering the Modbus devices. Verify that the Modbus address 
settings are unique for each device (i.e., no two devices with the same address) and power up the device. 
Connect each device in the chain by “daisy-chaining” the devices together . O and - polarity on the 
Modbus devices. For more information about Modbus loops, please read our  Modbus FAQ available at 
www.obvius.com 

Low Voltage analog, pulse, and RS485 wiring that enters electrical panels must have a minimum insulation rating 
that exceeds the voltage inside the panel.  In addition, other regulations may apply; consult the building codes in 
your area prior to installation.  

The RS485 port on the A8814 has a built in terminator.  A 150 ohm termination resistor should be placed at the 
other end of the RS485 loop, between the + and – wires.  For more information about RS485 termination, read 
the Modbus FAQ at www.obvius.com 

Some Modbus devices do not use the same label notation as the AcquiSuite.  Rather than +,-,S, Emon uses  Low, 
High, and Gnd.  To attach an Emon meter, use + to high,  - to low, and shield to gnd. 

The AcquiSuite A8814 built in electrical meter  uses Modbus address 250, and will show up in the Modbus device 
count as a single Modbus device. Additional meters and sensors can be added to the Modbus loop. 

 

Laptop/Computer Setup 

Step 1

 - You must have a computer to access and configure the AcquiSuite. This computer must have an ethernet 

connection (on the LAN or by direct connection) and must have a web browser installed such as Internet 
Explorer or Netscape. 

Note: If your building already has an existing LAN that the AcquiSuite is attached to, you can use an existing 
computer on that LAN. Check with your network administrator for details. If this option is available, use a LAN 
connected computer and skip to the “AcquiSuite administration overview” section below. 

 

Содержание AcquiSuite+ A8814



































Отзывы: