O'Brien FULTRONIC 1000 Скачать руководство пользователя

Страница: 35 / 44

DISPLACEMENT PUMP REPAIR

3. Tighten the packing retaining nut (211) onto the piston

valve (222) to 19 ft–lb (27 N.m).

Note the alignment

of the piston (222) to the packing

retainer nut (21 1). Maintain this alignment through

Steps 5, 6 and 7.

4. Place the ball (225) on the piston valve (222).

Refer

to Fig 35–1.

CAUTION

Step 5 is critical. Follow the procedure carefully to

avoid damaging the packings by overtightening.

5. Apply one drop of adhesive, supplied, to the threads

of the piston valve. Then hand tighten the valve as-

sembly into the piston rod just until the nut (211) con-

tacts the rod.

Refer to Fig 35–1.

211

TORQUE TO

10.5 in-lb (1.2 N.m)

to seat the packing,

and then back off and

tighten finger tight.

Fig 35–1

222

210*

203*

LIPS FACE DOWN

215*

225*

APPLY ONE DROP

OF SEALANT TO

THESE THREADS

LEATHER

*206

POLY

*212

LIPS FACE UP

224

6. Place the flats at the top of the rod in a vise.
7. Use a wrench to

CAREFULLY

tighten the nut (211)

onto the piston rod to 19 ft–lbs (25 N.m).

Refer to Fig

35–2.
Use two wrenches to maintain the alignment men-

tioned in Step 7, above.

Fig 35–2

224

211

TORQUE NUT

ONTO ROD TO

19 ft–lb

(27 N.m)

DO NOT ALLOW NUT

(211) TO MOVE

WHEN INSTALLING

PISTON ONTO ROD

8. One at a time stack the male gland (208*), alternate

the packings (213*,207*), and then install the female

gland (9), into the top of the cylinder (219).

Refer to

Fig 35–3.

9. Install the packing nut (216) and plug (205), but leave

loose for now.

Refer to Fig 35–3.

10. Coat the piston rod and packings with oil. Carefully

slide the assembly

INTO THE TOP OF THE SLEEVE

NOTE:

The tapered end of the sleeve is the bottom of it.

Refer to Fig 36–1.

11. Place a new o–ring (217*) firmly in the cylinder

groove.

Refer to Fig 35–3.

219

Fig 35–3

212*

POLY

LIPS MUST

FACE UP

213*

POLY

LIPS MUST

FACE UP

205

*206

LEATHER

LIPS MUST

FACE UP

*203

U–CUP SEAL

LIPS MUST

FACE DOWN

215*
214*

*202

*217

*208

*207

LEATHER

LIPS MUST

FACE DOWN

*209

DETAIL OF

THROAT PACKINGS

DETAIL OF

PISTON PACKINGS

218

216

211

TORQUE TO:

67 ft-lb

(90 N.m)

*210

Содержание FULTRONIC 1000













































Результаты поиска

Содержание FULTRONIC 1000

Отзывы:

Похожие инструкции для FULTRONIC 1000

Бренды по названию

Популярные бренды

O'Brien FULTRONIC 1000, Руководство пользователя

Результаты поиска

Содержание FULTRONIC 1000

Отзывы:

Похожие инструкции для FULTRONIC 1000

Бренды по названию

Популярные бренды