NXP Semiconductors S32K3X4EVB-Q257 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 36

NXP Semiconductors S32K3X4EVB-Q257 Скачать руководство пользователя страница 17

NXP Semiconductors

S32K3X4EVB-Q257 | S32K3X4EVBQ257ND

HWUM

Hardware User Manual

S32K3X4EVB-Q257 HWUM

All Information provided in this document is subject to legal disclaimers

© NXP B.V. 2020. All rights reserved

NXP Semiconductors

REV B

– 9/2021

Page

17

of

36

5-6

The NPN external Ballast transistor is selected to supply
the V15_MCU domain.

Default

closed

OPEN

The V15_MCU domain is disconnected and isolated
from the local external supplies.

8 Programming and Debug Interface

8.1 RESET Switch and LED indicator

The RESET switch [SW2] provides for manual application of the RESET input signal. The S32K3 MCU will drive the RESET signal to
reset the EVB board peripherals. The RESET LED indicator [D22] will be ON for the duration of the RESET signal. This operation indicates
the S32K344 MCU is in the Reset state.

Figure 12. S32K3X4EVB-Q257 | S32K3X4EVBQ257ND

– RESET Switch

8.2 On-board S32K3 Debugger

The S32K3X4EVB-Q257 [only] incorporates an On-Board Debugger embedded well as JTAG connectors. It bridges serial and debug
communications between a USB host and an embedded target processor.

«
...
15
16
17
18
19
...
»

Содержание S32K3X4EVB-Q257





































Отзывы:

Нет отзывов