manualshive.com logo in svg

NXP Semiconductors MKW01Z128, Справочное руководство

NXP Semiconductors MKW01Z128 - бесплатное руководство по эксплуатации доступно для скачивания с manualshive.com. Этот справочник содержит полезные инструкции для использования продукта и позволит вам максимально эффективно использовать все его возможности. Безусловно, скачайте его прямо сейчас!

Поделиться
Скачать
background image

31.4.5.1 Transmit by DMA

Transmit by DMA is supported only when TXDMAE is set. A transmit DMA request is
asserted when both SPE and SPTEF are set. Then the on-chip DMA controller detects
this request and transfers data from memory into the SPI data register. After that, TX
DMA DONE is asserted to clear SPTEF automatically. This process repeats until all data
for transmission (the number is decided by the configuration register[s] of the DMA
controller) is sent.

When the FIFO feature is supported: In FIFO mode (FIFOMODE=1) and when a data
length of 8 bits is selected (SPIMODE=0), the DMA transfer for one transmit DMA
request can write more than 1 byte (up to 8 bytes) to the DL register because the TX
FIFO can store 8 bytes of transmit data. In FIFO mode (FIFOMODE=1) and when a data
length of 16 bits is selected (SPIMODE=1), the DMA transfer for one transmit DMA
request can write more than 1 word (up to 4 words) to the DH:DL registers because the
TX FIFO can store 4 words of transmit data. A larger number of bytes or words
transferred from memory to the SPI data register for each transmit DMA request results
in a lower total number of transmit DMA requests.

When FIFOMODE is 0: Cycle Steal (DMA_DCRn[CS] = 1) should be enabled when
using the DMA controller to transfer data from memory to the SPI data register. The
DMA performs a single data transfer per DMA request in cycle steal mode. Therefore, a
single byte/word is written to the SPI data register from memory and transmitted by the
SPI module for each DMA request, as long as the BCR value is greater than zero
(DMA_DSR_BCRn[BCR] > 0). Once the BCR has reached zero, software must
reconfigure the DMA controller if more data is to be transmitted. If a configuration error
occurs (DMA_DSR_BCRn[CE] = 1) when the BCR is equal to 0, software must:

• disable peripheral requests when the BCR is equal to 0,
• perform 16-bit transfers (SPIMODE = 1), or
• decrease the SPI baud rate.

Software can disable peripheral requests by setting DMA_DCRn[D_REQ] = 1 when
initializing the DMA controller, or by clearing DMA_DCRn[ERQ] once the BCR is
equal to zero. Also, to continue transmitting data software must re-enable peripheral
requests (DMA_DCRn[ERQ] = 1) after reconfiguring the DMA controller.

31.4.5.2 Receive by DMA

Receive by DMA is supported only when RXDMAE is set. A receive DMA request is
asserted when both SPE and SPRF are set. Then the on-chip DMA controller detects this
request and transfers data from the SPI data register into memory. After that, RX DMA
DONE is asserted to clear SPRF automatically. This process repeats until all data to be

Functional description

MKW01Z128 MCU Reference Manual, Rev. 3, 04/2016

602

Freescale Semiconductor, Inc.

Содержание MKW01Z128





















































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MKW01Z128

W.E. Anderson 2800 Series Installation And Operating Instructions preview
2800 Series
Бренд: W.E. Anderson Страницы: 4
Harman Kardon AVR 3700 Quick Start Manual preview
AVR 3700
Бренд: Harman Kardon Страницы: 10
Harman Kardon AVR 254 Quick Start Manual preview
AVR 254
Бренд: Harman Kardon Страницы: 2
JAROLIFT TDRCT-04 Operating Instructions Manual preview
TDRCT-04
Бренд: JAROLIFT Страницы: 6
JAROLIFT TDRR-01W Operating Manual preview
TDRR-01W
Бренд: JAROLIFT Страницы: 8
Danfoss EMP 2 Installation Manual preview
EMP 2
Бренд: Danfoss Страницы: 2
Michell Instruments SF72 User Manual preview
SF72
Бренд: Michell Instruments Страницы: 28
Cooper 703EUR-00 Installation And Programming Manual preview
703EUR-00
Бренд: Cooper Страницы: 120
B&G Network V50 VHF Installation Instructions Manual preview
V50 VHF
Бренд: B&G Network Страницы: 22
Icom IC-U400 Owner'S Manual preview
IC-U400
Бренд: Icom Страницы: 16
Sangean WFR-70 User Manual preview
WFR-70
Бренд: Sangean Страницы: 84
Gewa BigJack IR-6SP Manual preview
BigJack IR-6SP
Бренд: Gewa Страницы: 36
Luxman 6.1 Channel AV Reciever LR-6500 Owner'S Manual preview
6.1 Channel AV Reciever LR-6500
Бренд: Luxman Страницы: 36
Harman Kardon TA260 Instruction Manual preview
TA260
Бренд: Harman Kardon Страницы: 15
FlexRadio Systems FLEX-6000 Signature Series Quick Start Manual preview
FLEX-6000 Signature Series
Бренд: FlexRadio Systems Страницы: 24
PCB Piezotronics IMI Sensors 682C33 Installation And Operating Manual preview
IMI Sensors 682C33
Бренд: PCB Piezotronics Страницы: 22
Sam ADCL-200 Technical Notice preview
ADCL-200
Бренд: Sam Страницы: 20
Agilent Technologies HFBR 5203 Technical Data Manual preview
HFBR 5203
Бренд: Agilent Technologies Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды