NXP Semiconductors freescale KV4 Series Скачать руководство пользователя | Manualshive

Страница: 762 / 1359

background image

The data buffer can be configured to operate in Normal mode, Swing mode, One-Time
Scan mode or FIFO mode. When the buffer operation is switched from one mode to
another, the read pointer does not change. The read pointer can be set to any value
between 0 and C2[DACBFUP] by writing C2[DACBFRP].

36.6.1.1 DAC data buffer interrupts

There are several interrupts and associated flags that can be configured for the DAC
buffer. SR[DACBFRPBF] is set when the DAC buffer read pointer reaches the DAC
buffer upper limit, that is, C2[DACBFRP] = C2[DACBFUP]. SR[DACBFRPTF] is set
when the DAC read pointer is equal to the start position, 0. Finally, SR[DACBFWMF] is
set when the DAC buffer read pointer has reached the position defined by
C1[DACBFWM]. C1[DACBFWM] can be used to generate an interrupt when the DAC
buffer read pointer is between 1 to 4 words from C2[DACBFUP].

36.6.1.2 Modes of DAC data buffer operation

The following table describes the different modes of data buffer operation for the DAC
module.

Table 36-40. Modes of DAC data buffer operation

Modes

Description

Buffer Normal mode

This is the default mode. The buffer works as a circular buffer.
The read pointer increases by one, every time the trigger
occurs. When the read pointer reaches the upper limit, it goes
to 0 directly in the next trigger event.

Buffer Swing mode

This mode is similar to the normal mode. However, when the
read pointer reaches the upper limit, it does not go to 0. It will
descend by 1 in the next trigger events until 0 is reached.

Buffer One-time Scan mode

The read pointer increases by 1 every time the trigger occurs.
When it reaches the upper limit, it stops there. If read pointer
is reset to the address other than the upper limit, it will
increase to the upper address and stop there again.

NOTE: If the software set the read pointer to the upper limit,

the read pointer will not advance in this mode.

FIFO Mode

In FIFO mode, the buffer is organized as a FIFO. For a valid
write to any DACDATx, the data is put into the FIFO, and the
write pointer is automatically incremented. The module is
connected internally to a 32bit interface. For any 16bit or 8bit
FIFO access, address bit[1] needs to be 0; otherwise, the
write is ignored. For any 32bit FIFO access, the Write_Pointer
needs to be an EVEN number; otherwise, the write is ignored.

Functional description

KV4x Reference Manual, Rev. 2, 02/2015

762

Preliminary

Freescale Semiconductor, Inc.

«
...
760
761
762
763
764
...
»

Содержание freescale KV4 Series
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для freescale KV4 Series

Бренд: Harmonic Drive Страницы: 25

Бренд: Nelson Страницы: 8

Бренд: Parker Страницы: 44

Бренд: Parker Страницы: 12

Бренд: Ultratec Страницы: 33

Бренд: Teledyne Страницы: 102

Бренд: Grundfos Страницы: 80

Tunnel Master Jr

Бренд: ICS Страницы: 70

Бренд: V2 Страницы: 108

Alicat Scientific MC

Бренд: Halma Страницы: 2

YukonDrive-1021

Бренд: Harmonic Drive Страницы: 53

Бренд: Unika Страницы: 4

Бренд: YASKAWA Страницы: 28

Бренд: Linear Technology Страницы: 6

Бренд: Ricoh Страницы: 190

Бренд: Progres Страницы: 2

Бренд: IBM Страницы: 104

Бренд: V2 Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды