Nvidia Jetson AGX Xavier Series Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 157

background image

Power

Jetson AGX Xavier Series Product

DG-09840-001_v2.5 | 19

Power Rails

Usage

(V)

Power Supply

Source

VDDIO_AO_3V3

SoC VDDIO_AUDIO_HV and VDDIO_AO_HV rails

3.3

PMIC LDO2

SYS_VIN_MV

VDD_EMMC_3V3

eMMC device 3.3V rail

3.3

PMIC LDO3

SYS_VIN_MV

VDD_USB_3V3

SoC AVDD_USB rail

3.3

PMIC LDO5

SYS_VIN_MV

VDD_SDIO_3V3

SoC VDDIO_SDMMC1_HV and
VDDIO_SDMMC3_HV rails

3.3

PMIC LDO6

SYS_VIN_MV

DDR_VDD2_1.1V

SoC VDDIO_VDD2_DDRx and DRAM VDD2 rails.

1.1

LTC3636

SYS_VIN_HV

VDD_DDRQ

VDDIO_DDRxLV and LPDDR4x VDDQ rails

0.6 LPDDR4x LTC3636

SYS_VIN_HV

Notes:

1.

SoC AVDD_PLL_NVHS_EUTMIP, VDD_HDMI_DP_PLL_0_1/1_3, PEX_HVDD, NVHS0_HVDD and NVHS0_PLL0_HVDD rails

2.

SoC VDDIO_UART/AUDIO/SDMMC4/DMMC3_HV_VCLAMP/ VDDIO_SDMMC1_HV_VCLAMP/CONN/EQOS/QSPI/,
AVDD_PLL_AA1_CV_ADC/DD2D3D4DPHBCS/CC2C3PADC_BPMP/C4_REFE, eMMC device VCCQ and QSPI device VDD rails.

3.

These rails are sourced from the PMIC Switcher SD2 used for VDDIO_SYS_1V8LS which is sourced from SYS_VIN_MV.

4.

SoC VDDIO_EDP/PEX_CTL/DEBUG/CAM/AO/VREFR0/ SYS, VPP_FUSE, AVDD_PLL_AON/MSC/GADC_M/MSD/XADC_MSB,
VCLAMP_USB, AVDD_OSC, LPDDR4x device VDD1, Temp Sensor VDD

5.

Enable (RUN2 pin) for VDD_DDRQ supply and Enable for discharge of DDR_VDD2_1.1V,
VDDIO_SYS_1V8HS/SYS_1V8LS/AO_1V8 rails.

5.2

Power Sequencing

The following list describes the basic power on sequencing requirements.



The main power source for the system is applied. The

SYS_VIN_HV

and

SYS_VIN_MV

are

derived from this power source. Optionally, these supplies can be gated and only enabled
to the module when a signal (such as

VIN_PWR_ON

) is enabled. This can help avoid damage

if the module is inserted when main power is on.



VDDIN_PWR_BAD_N

should stay active (low) until both

SYS_VIN_HV/MV

are valid (and not

gated).



MODULE_POWER_ON

can be set active (high) once

VDDIN_PWR_BAD_N

is inactive (high).



As the module powers on, one of the last supplies is the 3.3V supply always-on supply.

CARRIER_POWER_ON

is pulled up to the powergood pin of the 3.3V supply. Once this signal is

active (high), the carrier board supplies associated with the module (1.8V, 3.3V) can power
on.



SYS_RESET_N

is driven by the PMIC on the module during power-on. It does not need to be

controlled by the carrier board. If the carrier board supplies required for powering on
require additional time, the

PERIPHERAL_RESET_N

signal can be held low. This will keep the

SoC and other boot devices in reset.

«
...
32
33
34
35
36
...
»

Содержание Jetson AGX Xavier Series






























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Jetson AGX Xavier Series

Бренд: NEC Страницы: 10

Бренд: NEC Страницы: 8

Бренд: Amperes Страницы: 8

Бренд: Q-See Страницы: 2

ThunderLAN TNETE100A

Бренд: Texas Instruments Страницы: 179

Бренд: Supermicro Страницы: 16

Бренд: ESD Страницы: 28

Бренд: Grizzly Страницы: 9

Бренд: Cisco MERAKI Страницы: 4

Бренд: Kramer Страницы: 2

CNPS11X Extreme

Бренд: ZALMAN Страницы: 12

Бренд: ZALMAN Страницы: 18

Industrial Network Track OSI

Бренд: GarrettCom Страницы: 10

2410SA - Serial ATA RAID Controller

Бренд: Adaptec Страницы: 14

Бренд: IBM Страницы: 130

Advanced Flame 1.0

Бренд: Eastern Voltage Research Страницы: 12

Бренд: ADTRAN Страницы: 9

Бренд: TEC Control Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды