background image

 

Operating Instruction and Documentation 

                                                                                                                        

2.30 SPL                      

 

- 19 - 

•  The hydraulic oil has to be changed at least once a year. To change the oil, lower the lift into 

its lowest position. Empty all tanks and refill with clean oil, approx. 17 litres per hydraulic unit 
are needed.  

 

Use an ATF-Suffix hydraulic-oil (OEST Company ) if the ambient temperature is under 5 
degrees centigrade. After filling, the hydraulic oil must be between the upper and lower 
markings of the oil level gauge.  

 

Remove the old oil according to the appropriate regulations.  

•    Check all welded joints for cracks on the automotive-lift.    

If any cracks are found on the lift cease use immediately. Switch-off and secure the main 

switch (lock) and call the service partner. 

•   Ensure that the rubber-pads on the arms remain in good condition. 

Check the lockable pneumatic safety device to ensure that it is functioning correctly. 

•    Check all surfaces and repair if necessary. 
•  Damage to external surfaces, must be immediately repaired. 

If theses repairs are not made immediately, permanent damage to the powder-coated 
surface may result. 
Repair and clean  damaged areas with an abrasive paper (grain 120). After this is complete, 
use a suitable paint (observe the RAL Number). 

•   Check the zinc surface and repair it with a suitable tool. Use abrasive paper (grain 280). 

White rust can result from moisture laying in certain areas for long periods of time. Poor 
aerating can also result in rust formation.  
Rust may result from mechanical damage, wear, aggressive sediments (de-icing salt, liquids) 
or insufficient cleaning. 

 

Repair and clean these areas with abrasive paper (grain 280). 
After this is complete, use a suitable paint (observe the RAL Number).

 

•  Check all the safety devices of the lift. 
•  Check the controller Battery (ASC). The Battery has a working life (at normal operation) 

between 4 ½ - 5 Years (manufacturers statement).  To avoid permanent data-loss because 
of a flat battery, the ASC must be sent to Nussbaum headquarters  after 4 years of use. 
Please contact your service partner for details. 

 

 

•  Check the electric cable and channels for  Damage.  

 

Check that all screws and bolts are correctly torque (turning moments, see the list) 

 

pic. 2: 

 
7.2  Cleaning of the automotive lift 

 

 

 

A regular and appropriate maintenance served the preservation of the lift. 
It can be a prerequisite for claims at possible corrosion. 
The best protection for the lift is the regular cleaning of dirt of all manner. 
- Including this: 

Содержание 2.30 SPL











































Отзывы: