background image

6

PIPA lite series instructions

   7

PIPA lite series instructions

WARNING

Failure to follow these warnings, instructions 

and labels on the child restraint could result 

in serious injury or death. 

A child’s safety is your responsibility. 

NEVER 

leave your child unattended. 

Read all instructions before use of this 

child restraint or installation in a vehicle. 

In addition, read the vehicle owner’s 

manual for information on child restraint 

installation. 

Use the bottom of the base for storage of 

the instruction manual.

This child restraint can 

ONLY

 be used 

in a rear facing position when used in a 

vehicle and 

MUST

 be installed in a vehicle 

with the base. This child restraint cannot 

be properly secured in a forward facing 

position or without a base. Use only with 

children who weigh between 4 and 32 

pounds (2 and 14.5 kg) and whose height 

is  32 inches (81 cm) or less. Exceeding 

these height and weight limits is unsafe.

Snugly adjust the belts provided with 

this child restraint around your child. If 

straps are not snugly adjusted, child may 

be ejected from seat in the event of an 

accident.

A snug strap should not allow any slack. 

It lies in a relatively straight line without 

sagging. It does not press on the child’s 

flesh or push the child’s body into an 

unnatural position.

Register your child restraint with  the 

manufacturer.
Cover the child restraint when your vehicle 

is parked in sunlight. Parts of a child 

restraint can become very hot if left in the 

sun, and can burn a child’s skin. Check for 

hot parts before putting your child in the 

child restraint.
Replace this child restraint if it has been 

involved in a crash, even if it was minor 

and there appears to be no damage to the 

child restraint.

EXPIRATION DATE

 Check the label on the 

underside of the base or child restraint for 

expiration date information.

FALL HAZARD

 Child’s activity can move 

carrier. NEVER place carrier on counter 

tops, tables, or any other elevated surface. 

Always stay within arms reach whenever 

carrier is not on floor/ground. Be sure 

handle locks into position before lifting 

carrier. 

STRANGULATION HAZARD 

Children 

have strangled in loose or partially buckled 

harness straps. Fully restrain the child even 

when carrier is used outside the vehicle. 

SUFFOCATION HAZARD

 Infant carrier can 

roll over on soft surfaces and suffocate 

child. Never place carrier on beds, sofas, 

or other soft surfaces.

ALWAYS

 check child restraint to base 

connection. 

Содержание Pipa Lite Series



























Отзывы: