manualshive.com logo in svg

Numatic CRO 8055/100T, Инструкция пользователя, Страница: 26 / 28

Поделиться
Скачать
Numatic CRO 8055/100T Скачать руководство пользователя страница 26

26

EU DECLARATION 

OF 

CONFORMITY

We hereby declare under our sole responsibility that the 

following equipment fulfi ls all the relevant provisions of the 

following EU Directives:

Machine Description: 

 

Scrubber Dryer   

Type: TTV, TRO, CRO series

Relevant standards upon which conformity is declared 

include:

IEC 60335-1 2001 + A1 2004 + A2 2006 + National 

Deviations

IEC 60335-2.72 Ed 2.0

EN 55014-1:2006

EN55014-2:1997+A1

EN61000-3-2:2006

EN61000-3-3:1995+A1+A2

BS EN 62233:2008
A technical construction fi le for this equipment is retained at 

the manufacturer’s address under the authorisation of the 

following signatory:

Signed: 

Date: 15/06/2015

Numatic International Limited,  

Chard , Somerset. 

TA20 2GB 

www.numatic.co.uk

GB

15

Position: Technical Manager

Name:Allyn Boyes 

 

Manufactured by: 

  Numatic International Limited

Machinery Directive 2006/42/EC

EMC Directive 2004/108/EC

RoHS Directive 2011/65/EU

Schematic Diagram

In the event of a breakdown contact your Numatic dealer or the

Numatic Technical help line +44 (0)1460 269268

EU Declaration of Conformity

Содержание CRO 8055/100T





























Отзывы:

Нет отзывов