Nugen 7000XTR Скачать руководство пользователя страница 6

Страница: 6 / 44

Page 6

Timer Operation

Valve State:

INI (Initializing)

INI will display on the screen for 30 to 5 seconds when initializing after a power failure reset or programming.

RGQ (Regeneration Queued)

RGQ indicates that the reserve has been entered in a delayed system and regeneration has been queued.

When in the main screen, press the Shift button to toggle service (SRV) with RGQ.

Service (SRV)

SRV will display when the unit is in service.

LED Status Lights:

Blue LED:

Illuminates while the unit is in service and no errors exist. The unit will always be in service unless a

regeneration trigger has occurred (green LED light will be displayed).

Green LED:

Illuminates when the unit is in Regeneration mode, unless an error condition exists.

Red LED:

Illuminates when there is an error.

Flow Indicator:

A rotating line (appearing as a rotating star shape) will display on the screen when flow is going through the

the meter.

Содержание 7000XTR













































Результаты поиска

Содержание 7000XTR

Отзывы:

Похожие инструкции для 7000XTR

Бренды по названию

Популярные бренды

Nugen 7000XTR, Руководство по обслуживанию

Результаты поиска

Содержание 7000XTR

Отзывы:

Похожие инструкции для 7000XTR

Бренды по названию

Популярные бренды