7
i. Setting the Timer Programs P1 and P2 for Daytime & Night Time Settings.
.
The Timer Programs are identified by the symbols P1 and P2 on the screen and each can be set for both daytime
(sun symbol) and night time (moon symbol) settings.
Note :
Both Programs have to be set, you cannot just set one program, however you can set both at the same settings.
Setting the P1 (Program 1), On Time
.
Briefly Press the Set Button to scroll to TIMER Mode.
.
Hold the Set Button until P1 Sun Symbol (Daytime) is displayed and the time flashes.
.
Press the Large Flame button to set the Hour.
.
Press the Small Flame button to set the Minute.
Setting the P1 (Program 2), Off Time
.
Briefly
press the Set Button to scroll to the P1 Moon Symbol (Night time) is displayed and the time flashes.
.
Press the Large Flame button to set the Hour.
.
Press the Small Flame button to set the Minute.
Setting the P2 (Program2), On Time
.
The Screen will automatically proceed to setting the P2 Settings
.
Briefly Press the Set Button to scroll to the P2 Sun Symbol (Daytime) is displayed and the time flashes.
.
Press the Large Flame button to set the Hour.
.
Press the Small Flame button to set the Minute.
Setting the P2 (Program2), Off Time
.
Briefly
press the Set Button to scroll to the P2 Moon Symbol (Night time) is displayed and the time flashes.
.
Press the Large Flame button to set the Hour.
.
Press the Small Flame button to set the Minute.
.
Both Programs
Press Off or simply wait to return to the Manual Screen.
Note :
With the Programs now set the Handset will have to be left in the TIMER mode to enable the programs to control the fire.
2.5 - GENERAL - ALL THERMATRONIC CONTROLS
a.
Battery replacement is recommended at the beginning of each heating season, or when an acoustic error message sounds at ignition.
b.
Error Message – Long signals (0.8 second tone – 0.2 second break) during ignition – probable cause batteries in electronic receiver box
are nearly discharged.
c.
Error Message – 5 second continuous tone – probable cause – cable disconnected or on/off switch on valve is in off position.
d.
Batteries - Electronic Receiver Box - 4 x AA good quality alkaline - Handset - 1 x PP3 good quality alkaline.
e.
To change the Handset battery slide open the plastic panel on the back of the Handset.
f.
To change the Receiver Batteries remove the Ash Pan Cover and locate the electronic receiver box, underneath the fire on the
left hand side. Slide open the plastic cover to gain access to the battery compartment. You can detach the Receiver by pulling it off its
Velcro Pad to make access easier but remember to put it back in the same position under the metal shield.
Note: Only Change The Batteries When The Fire Is Cold
2.6 - RESETTING THE MERTIK MAXITROL LOGIC CIRCUITS - IF THE HANDSET DOES NOT WORK
ONLY APPLIES TO THE THERMATRONIC HAND HELD RADIO FREQUENCY CONTROLS
Basic Reset -
It sometimes happens that (such as when the handset buttons are pressed out of sequence) the fire stops working
because the logic circuits get confused and need to be reset.
To do this, simply remove the 4 x AA batteries from the Receiver Box (see section 2.5f above), wait for 1 minute and then refit the batteries.
Wait for another minute and then point the handset at the fire and press the red/off button. Wait for another minute and then start the fire as
normal. If the fire does not start repeat the resetting procedure. If the fire still does not work a Full Reset can be tried (see next page).
Full Reset -
If you obtain a new handset the control system will need to learn the handset’s unique code via a Full Reset.
Also, if the fire is not working and the Basic Reset (described on page 7) has not worked a Full Reset can be carried out:
Remove the Ash Pan Cover and locate the electronic Receiver Box.
Locate the Reset Hole on the side of the Receiver and using a pen press and hold in the Reset button until you hear two beeps.
The first beep is short and the second beep is long. After the second beep release the Reset Button.
Now on the Handset, within the next 20 seconds press and hold the Small Flame Button until you hear two additional short beeps
confirming the code is set in the Receiver.
If you hear one long beep the Code as not been set so repeat the procedure.
If after carrying out the above procedure the situation is not corrected it will be necessary to contact your Installer.
Note: For the Installation/Service Engineer
- Resetting of the Handset & Control System is also covered in Section 21.1 page 32.
