background image

NRG INSTRUCTIONS

 

 

 

Windcube PV Trailer

  

 

 

 

Windcube_PVTrailer_ModerateClimate_Instructions 
Rev. 2 

[email protected] | Page 8 

 27 March 2018 

Section 4: Anchoring 

The trailer ships with four small screw-in earth anchors that can be used if additional stability is desired. There are two 
anchor points on either side of the trailer:  

 

 

 

1.

 

Attach one end of the anchor cable to the anchor points on the sides of the trailer. 

2.

 

Unscrew the turn buckle until it is extended as far as it can go. 

3.

 

Pull the anchor cables out to the sides at about a 45° angle.  

4.

 

Take note of where the end of the cable comes to on the ground. Come in some and 
screw the anchors straight down into the ground using a metal bar.  

5.

 

Attach the anchor cable to the end of the anchor and pull excess cable thru wire rope 
clips and tighten clips back up. 

6.

 

Adjust final tension with turnbuckles.  

7.

 

Repeat at the remaining three anchor points and then tighten them all down to be the 
same tension. 

Section 5: Connect Windcube, modem and power monitor 

Typically, the Windcube’s modem should be moved to the trailer control box to share communications with the PV 
power monitor.  

1.

 

Remove the modem from the Windcube 

a.

 

Open the back door (opposite connection panel). 

b.

 

Remove the modem Ethernet, antenna and power connections (3/8” wrench for antenna). 

c.

 

Remove the modem (if not already installed in the trailer).  

d.

 

Close the back door and open the front door. 

e.

 

Locate P2 on the bottom rack (4

th

 from right, see picture below). 

f.

 

Disconnect the WHITE cable from P2 – pull the collar straight back. 

g.

 

Connect the BLACK cable to P2 – line up the red dots and push the collar straight in. 

Содержание Windcube














Отзывы: