Controller N1200
NOVUS AUTOMATION
3 / 13
Using the Alarm 1 as example.
difk
– Alarm of Maximum Differential Value
Triggers when the value of PV is
above
the defined point by:
(SP + SPA1)
Using the Alarm 1 as example.
SCREEN
TYPE
ACTUATION
Off
Inoperative
Output is not used as alarm.
Ierr
Open sensor
(
i
nput
Err
or)
Activated when the input signal of PV is
interrupted, out of the range limits or Pt100
in short-circuit.
Rs
Event (
r
amp and
S
oak)
Activated in a specific segment of program.
rfail
Resist. burnt out
(resistance
fail
)
Signals a failure in the heating element.
Lo
Minimum value
(
Lo
w)
SPAn
PV
Ki
Maximum value
(
Hi
gh)
SPAn
PV
Dif
Differential
(
diF
erential)
SV
PV
SV + SPAn
alarme
SV - SPAn
alarme
SV
PV
SV - SPAn
alarme
SV + SPAn
alarme
Positive SPAn
Negative SPAn
Difl
Minimum
Differential
(
diF
erential
L
ow)
Positive SPAn Negative SPAn
SV
PV
SV - SPAn
SV
PV
SV - SPAn
Difk
Maximum
differential
(
diF
erential
H
igh)
SV
PV
SV + SPAn
SV
PV
SV + SPAn
Positive SPAn
Negative SPAn
Table 3
– Alarm Functions
Where SPAn refers to Setpoints of Alarm “
SPA1
”, “
SPA2
”,
“
SPA3
” and “
SPA4
”.
ALARM TIMER MODES
The controller alarms can be configured to perform 3 timer modes:
One pulse with defined duration;
Delayed activation;
Repetitive pulses;
The illustrations in
Table 4
show the behavior of the alarm output for
various combinations of times t1 and t2. The timer functions can be
configured in parameters
A1t1
,
A1t2
,
A2t1
,
A2t2
,
A3t1
,
A3t2
,
A4t1
and
A4t2
.
OPERATION
T 1
T 2
ACTION
Normal
Operation
0
0
Alarm Event
Alarm
Output
Activation for
a defined time 1 to 6500 s
0
Alarm Event
Alarm
Output
T1
Activation with
delay
0
1 to 6500 s
Alarm Event
Alarm
Output
T2
Intermittent
Activation 1 to 6500 s 1 to 6500 s
Alarm Event
Alarm
Output
alarme
T1
T2
T1
Table 4
– Temporization Functions for the Alarms
The LEDs associated to the alarms will light when the alarm
condition is recognized, not following the actual state of the output,
which may be temporarily OFF because of the temporization.
INITIAL BLOCKING OF ALARM
The initial blocking option inhibits the alarm from being recognized if
an alarm condition is present when the controller is first energized (or
after a transition from run YES
NO). The alarm will be enabled
only after the occurrence of a non-alarm condition followed by a new
occurrence for the alarm.
The initial blocking is useful, for instance, when one of the alarms is
configured as a minimum value alarm, causing the activation of the
alarm soon upon the process start-up, an occurrence that may be
undesirable.
The initial blocking is disabled for the sensor break alarm function.
EXTRACTION OF THE SQUARE ROOT
With this feature enabled the controller uses for display and control a
value that corresponds to the square root of the applied input signal.
Available only for the inputs belonging to the group of linear analogic
signals: 0-20 mA, 4-20 mA, 0-50 mV, 0-5 V and 0-10 V.
ANALOG RETRANSMISSION OF PV AND SP
The analog output, when not used for control purposes, is available
for retransmitting the PV and SP values in 0-20 or 4-20 mA. This
analog output is electrically isolated from other inputs and outputs.
The analog output signal is scalable, with the output range defined by
the values programmed in the parameters “
rtLL
” and “
rtkL
”.
To obtain a voltage output, the user must install a resistor shunt (550
max.) to the current output terminals (terminals 7 and 8). The
actual resistor value depends on the desired output voltage span.
There is
no electrical isolation
between serial communication
(RS485) and channel I/O5.
SOFT-START
The soft-start feature avoids abrupt variations in the power delivered
to the load regardless of the system power demand. .
This is accomplished by defining a limiting ramp for the control output.
The output is allowed to reach maximum value (100 %) only after the
time programmed in the soft-start parameter has elapsed. The Soft-
start function is generally used in processes that require slow start-up,
where the instantaneous application of 100 % of the available power to
the load may cause damages to parts of the system.
In order to disable this function, the soft-start parameter must be
configured with 0 (zero).
REMOTE SETPOINT
The controller can have its Setpoint value defined by an analog,
remotely generated signal. This feature is enabled through the
channels I/O3, I/O4 or I/O5 when configured as digital inputs and
configured with the function
rsp
(Remote SP selection) or through
the parameter
E.rsp
. The remote setpoint input accepts the signals
0-20 mA, 4-20 mA, 0-5 V and 0-10 V.
For the signals of 0-20 and 4-20 mA, a shunt resistor of
100
is
required between terminals 9 and 10, as shown in
Figure 4c
.
CONTROL MODE
The controller can operate in two different manners: Automatic mode
or Manual mode. In automatic mode the controller defines the amount
of power to be applied on the process, based on defined parameters
(SP, PID, etc.).
In the manual mode the user himself defines this amount of power.
The parameter
“
(trl
” defines the control mode to be adopted.
PID AUTOMATIC MODE
For the Automatic mode, there are two different strategies of control:
PID control and ON/OFF control.
PID control has its action based on a control algorithm that takes into
account the deviation of PV with respect to SP, the rate of change of
PV and the steady state error.
On the other hand, the ON/OFF control (obtained when Pb=0)
operates with 0 % or 100 % of power, when PV deviates from SP.