Terms of Guarantee
question are to be made available to us. We shall
not bear the costs for dismantling and installation,
freight and carriage. If a complaint is proven to be
unjustified, the customer must bear our costs. This
guarantee is only valid in conjunction with the
signed invoice and commences on the day of
delivery. The manufacturer guarantees that the
product is free of defects. The warranty is granted
for a period of 24 months, in as far as the
verification overleaf has been properly filled out.
Otherwise the warranty shall expire 27 months
after the date of manufacture.
maintenance, excessive use and overloading as
well as any alterations or modifications carried
out to the operator and accessory parts by the
customer. The same shall also apply for damage
incurred during transit or as a result of force
majeure, external influences or natural wear as
well as special atmospherical stresses. We
cannot accept any liability following alterations or
modifications of functional parts carried out by the
customer. We must be notified of any defects
immediately in writing; on request the parts in
Dear customer,
During production the control unit you have
purchased has undergone various checks by the
manufacturer to ensure that it is of impeccable
quality. Should this operator or parts of it prove to
be of no use or limited use as a result of proven
material or manufacturing defects, we shall
rectify this, at our discretion, through free-of-
charge repair or replacement. We shall not
accept any liability for damage as a result of
unsatisfactory fitting and installation, improper
putting into service, incorrect operation and
Programming the control unit
The programming is menu-driven. Carry out
adjustment of the door in accordance with the
scheme. The following page shows the full extent of
the menu.
Set the correct motor and brake type before
setting the end positions (menus 78 and 79).
!
Wrong setting can damage the door.
No door type selected: E01 is displayed.
Brake selection
(menu 78)
Brake type A, currentless braking, is applied at the
same time (value=0) or with a delay (1-9) after start
of the motor.
Brake type B, currentless opening, opens at the
same time (value=10) or with a delay (11-19) after
start of the motor.
Drive motor selection
(menu 79)
The drive motors are listed on a separate sheet
because new additions are made constantly.
Setting the door end-of-travel positions
(menus
30 and 31)
The top and bottom end positions should be set
directly one after the other.The door end positions
will be approached in the dead-man mode. Let the
button go before reaching the required end position.
Fine adjustment in menu 33/34.
No closing edge or light barrier monitoring
.
activated while the door is moving
Door motion settings
(menus 70 and 79)
Related parameters such as maximum motor speed
and optimum door motion profile are stored for every
motor type.
These settings could be necessary depending
!
the door type.
on
ON period
(menu 49)
The ON period set will prevent the drive motor from
getting overheated and thus getting damaged.
RWA (smoke-heat exhaust) function
Set the required door position in menu 55. Connect
fire alarm to J7 and set value 10 in menu 50.
Programming the radio remote control
Please note that each hand transmitter must be
individually programmed. It is possible for up to 30
radio codes to be learned. The required function can
be selected in menu 64.
KeeLoq, 12 Bit Multibit. The first code determines the
type.
Start impulse
(menu 60)
Enter the menu and press the button on the hand
transmitter for the START function. As soon as the
code has been learned, the incremental display
flashes five times.
Half-open position of the door
(menu 61)
Enter the menu and press the button on the hand
transmitter for the half-open position. As soon as the
code has been learned, the incremental display
flashes five times.
Light function
(menu 62)
Enter the menu and press the button on the hand
transmitter for the light function. As soon as the code
has been learned, the incremental display flashes
five times.
Deleting radio codes
(menu 63)
To delete all the learned codes in the menu, press the
oval button and keep it pressed for 5 seconds.
Selection of the transmitter mode
(menu 64)
Additionally, the taught-in handheld transmitters can
be temporarily blocked in this menu, and the
required function can be selected there.
Wireless closing edge RadioBand
P
menu 35=4 and
ut module onto J14 and set
menu
53=5.
Observe the instructions concerning the RadioBand.
The function of terminal J3 will be deactivated.
Sensors connected with terminal J3 have
no function.
GB
