manualshive.com logo in svg

Novanta SYNRAD Pulstar p100, Руководство пользователя

Поделиться
Скачать
Novanta SYNRAD Pulstar p100 Скачать руководство пользователя страница 82

DC PRE-CHARGE FAULT 

PAGE 

|

 77 

over temperature fault, lower coolant temperature below 28 °C and then cycle DC power (remove DC 

power, wait 30 seconds, reapply DC power). When the RDY indicator illuminates, lasing is enabled after 

the five-second delay. If the TMP indicator remains red after cycling power, continue to flow cooling 

water through the laser for a few more minutes and/or verify the coolant flow rate and then cycle DC 

power again. 
 

Under Voltage fault 

This fault is indicated by the RDY LED flashing 1 blink. The Laser Ready Output Opens under these 

conditions. To reset an under-voltage fault, first correct the voltage problem and ensure that 48 VDC is 
measured at the laser’s DC power terminals. Next, cycle DC power off and then on again. When the RDY 

LED illuminates, the Laser Ready output Closes, and lasing is enabled after the five-second delay. Apply 
a PWM Command signal, provided the SHT indicator is illuminated blue.  

 

Over Voltage fault  

An over voltage fault occurs when DC input voltage rises above a preset limit of 49.5 VDC. This fault is 

indicated by the RDY LED flashing 2 blinks. Under these conditions the Laser Ready output Opens. To 

reset an over voltage fault first correct the voltage problem and ensure 48 VDC is measured at the 

laser’s DC power terminals. Next, cycle DC power off and then on again. When the RDY LED illuminates, 

the Laser Ready output Closes, and lasing is enabled (after a five-second delay) provided a PWM 

Command signal is applied, and the SHT indicator is illuminated blue. 
 

RF Drive Switch fault  

An RF Drive Switch fault occurs during power-up. RF drive switch faults are triggered by either of the 

following: the tube fails to breakdown, or the RF Driver’s 48-volt switching circuitry fails. A RF drive 
switch fault is indicated when the RDY LED flashes 3 blinks and the Laser Ready output Closes. If a RF 

Drive Switch fault occurs, the laser requires service-Contact Contact NOVANTA® Customer Service or a 
NOVANTA Authorized Distributor.  

 

PWM Drive fault  

A PWM Drive fault signals a problem in the laser’s internal RF circuitry and is indicated by a flashing RDY 

LED that blinks 4 times. If a PWM Drive fault appears, the laser requires service— please contact 
NOVANTA Customer Service or a NOVANTA Authorized Distributor.  

 

DC Pre-Charge fault  

A DC Pre-Charge fault indicates that 48 VDC is not available at the input of one or more of the RF 
modules. The RDY LED will flash in a 5-blink pattern. When this occurs, the Laser Ready output Opens. If 

a DC Pre-Charge fault appears, the laser requires service—please contact NOVANTA Customer Service 
or a NOVANTA Authorized Distributor.  

 

 

 

Содержание SYNRAD Pulstar p100


























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды