manualshive.com logo in svg

Novanta SYNRAD Pulstar p100, Руководство пользователя

Поделиться
Скачать
Novanta SYNRAD Pulstar p100 Скачать руководство пользователя страница 56

INPUT/OUTPUT SIGNALS 

PAGE 

|

 51 

P100/150’s optically-isolated outputs are useful for sending laser status to a Programmable Logic 

Controller (PLC) or computerized control system. Each of the five outputs can source 50 mA at ±24 

VDC maximum for a total load of 250 mA. For controlling larger loads, use these outputs to drive a 

control relay. 

 

Important Note: Interlock Open and Shutter Open output signals are dependent control 

functions. The Shutter Open output will not close (SHT LED On) until a Shutter Open Request 

signal is applied and the Interlock Open output opens (causing INT LED to illuminate green and RDY LED 

to turn on). 
 
Pin 6    Laser Active  

•

 

This bi-directional switched output is internally connected to Pin 13, Output Common, when the 

laser is actively lasing (LASE indicator red). This output is open (high impedance) when no beam 

is being emitted (LASE indicator Off). Refer to Table 4-5 for output circuit specifications.  

Pin 7    Fault Detected  

•

 

This bi-directional switched output is internally connected to Pin 13, Output Common, when (1) an 

over-temperature fault (TMP LED is red) or (2) a No-Strike condition (blue SHT indicator is 

flashing) has occurred. The output is open (high impedance) when laser operation is within limits 

(TMP LED green and SHT LED blue). Refer to Table 5-5 for output circuit specifications.  

Pin 8    Laser Ready  

•

 

This bi-directional switched output is internally connected to Pin 13, Output Common, when the 

laser is enabled (RDY indicator on), indicating that lasing will occur when a PWM Command 

signal is applied to Pin 9 and Pin 1. When this output is initially switched closed, there is a five-

second delay during which lasing is inhibited. This output is open (high impedance) when the 

laser is disabled (RDY LED Off). Refer to following output circuit specifications table.  

Pin 13   Output Common  

•

 

Use this pin to complete the return (ground) path for any output connection (Pin 6, 7, 8, 14, or 15). 

The Output Common line is protected by a 0.3 A self-resetting fuse.  

Pin 14   Shutter Open  

•

 

This bi-directional switched output is internally connected to Pin 13, Output Common, when 

Remote Interlock and Shutter Open Request signals are present (SHT LED blue and RDY LED 

yellow), indicating that lasing is enabled. This output is open (high impedance) when the laser is 

disabled (SHT LED Off). Refer to following output circuit specifications table. 

Pin 15   Interlock Open  

•

 

This bi-directional switched output is internally connected to Pin 13, Output Common, when 

remote interlock input circuitry is open (INT indicator red), indicating that lasing is disabled. This 

output is open (high impedance) when the laser is enabled (INT indicator green). When this 

output is initially switched open, there is a five-second delay during which lasing is inhibited. See 

Table 5-5 for output circuit specifications

.

 

 
 
 
 

Содержание SYNRAD Pulstar p100


























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды