Novanta SYNRAD Pulstar p100 Скачать руководство пользователя страница 73

Страница: 73 / 89

MAINTENANCE AND TROUBLESHOOTING

PAGE

Maintenance and Troubleshooting

Use the information in this section to perform maintenance or troubleshoot your

p100/150 laser.

•

Maintenance – describes typical p100/150 maintenance procedures.

•

Troubleshooting – explains how to troubleshoot common p100/150 problems.

Important Note: This section of the Operation Manual explains how to conduct regular main-

tenance and/or basic troubleshooting to p100/150 lasers. If you cannot attend to the unit using

the information described in this manual, contact NOVANTA®, (+.425.349.3500) or an authorized

NOVANTA Distributor.

Maintenance

The Maintenance section includes subsections:

•

Disabling the p100/150 laser

•

Daily Inspections

•

Storage/shipping

•

Cleaning optical components

Disabling the p100/p150 laser

Before performing any maintenance on your

p100/150 laser, be sure to completely disable the laser by

disconnecting the DC Power Cables from the DC power supply.

Caution: Possible Equipment Damage

Inlet cooling water temperature must always be maintained above the dew point to prevent

condensation and water damage to your laser.
-Or-
Use purge gas to prevent condensation damage if the dew point is over 22°C

Do not exceed a gas purge pressure of 34.5 kPa (5 PSIDo not use argon as a purge gas.

Use only nitrogen or clean, dry air as described in the in this chapter.

Caution: Possible Equipment Damage

If you operate the laser in dirty or dusty environments, contact NOVANTA® about the risks of doing so
and precautions you can take to increase the longevity for the laser system and associated optical

components.

Содержание SYNRAD Pulstar p100


























































































Результаты поиска

Содержание SYNRAD Pulstar p100

Отзывы:

Бренды по названию

Популярные бренды

Novanta SYNRAD Pulstar p100, Руководство пользователя

Результаты поиска

Содержание SYNRAD Pulstar p100

Отзывы:

Бренды по названию

Популярные бренды