Novanta SYNRAD Pulstar p100 Скачать руководство пользователя страница 8

Страница: 8 / 89

INTRODUCTION SUMMARY

PAGE

Introduction summary

p100/150 Trademark, copyright, contact (service & support) information &

Nomenclature

Important Notes:

•

This Operation Manual explains operation activities related to p100/150 lasers. If you cannot

operate the unit using the information described in this manual, contact NOVANTA®

(+1.425.349.3500) or an authorized NOVANTA Distributor.

•

Lift the laser only by the mounting feet or baseplate. Do not lift or support the laser by its cooling

fittings.

•

Please reference the Quick Start Guide for unpacking, mounting, and connecting.

•

Failure to properly package the laser using NOVANTA shipping box and foam/cardboard inserts

as shown in Packaging Instructions may void the warranty. Customers may incur additional repair

charges due to shipping damage caused by improper packaging.

•

Before beginning any maintenance or inspections of your p100/150 laser, be sure to completely

disable the laser by disconnecting the DC Power cable (or cables) from the rear of the laser.

•

A risk of exposure to toxic elements may result when certain optical or beam delivery

components are damaged. In the event of damage to laser, marking head, or beam delivery

optics, contact NOVANTA, or the optics manufacturer for handling instructions.

•

If you operate your laser in dirty or dusty environments, contact NOVANTA about the risks of

doing so and precautions you can take to increase the longevity of your laser, marking head, and

associated optical components.

•

Remote interlock faults are not latched on OEM lasers. Clearing the fault condition re-enables the

RDY indicator and the laser will fire immediately provided the SHT indicator is lit and a PWM

Command signal is applied.

•

Because exposure to CO2 laser radiation in the (9-11)

m range can inflict severe corneal injuries

and seriously burn human tissue, the OEM or System Integrator must ensure that appropriate

safeguards are in place to prevent unintended lasing.

•

A risk of exposure to toxic elements may result when certain op-tical or beam delivery

components are damaged. In the event of damage to laser, marking head, or beam delivery

optics, contact NOVANTA, or the optics manufacturer for handling instructions.

•

The use of the Quick Start Plug bypasses the laser’s safety inter-lock function, potentially

exposing personnel in the area to invisible infrared laser radiation. The Quick Start Plug is

intended only for initial testing and troubleshooting by qualified personnel. In normal operation,

the laser’s Remote Interlock input should be connected to the machine’s safety interlock circuitry.

Содержание SYNRAD Pulstar p100


























































































Результаты поиска

Содержание SYNRAD Pulstar p100

Отзывы:

Бренды по названию

Популярные бренды

Novanta SYNRAD Pulstar p100, Руководство пользователя

Результаты поиска

Содержание SYNRAD Pulstar p100

Отзывы:

Бренды по названию

Популярные бренды