Novanta Jadak Flexpoint HS-1R Скачать руководство пользователя страница 66

Страница: 66 / 82

Flexpoint™ HS-1R User’s Manual

Page 66

Compliance and IP Notices

Statement of Agency Compliance

The product is designed to support the following regulatory and safety standards as a standalone

unit. The end user will need to verify general EMC compliance as implemented in their host

system. The end user will not need to verify RFID radio compliance since JADAK LLC tested the

HS-1R and received modular certification for this portion of the product.

This HS-1R complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this HS-1R may not cause harmful interference and (2) this HS-1R must accept

any interference received, including interference that may cause undesired operation.

FCC Class B Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

HS-1R pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio or television technician for help.

Caution:

Any changes or modifications made to this HS-1R, which are not expressly approved

by JADAK, LLC may void the user’s authority to operate the equipment.

Note:

To maintain compliance with FCC Rules and Regulations, cables connected to this

HS1-M must be shielded cables, in which the cable’s shield wire(s) have been grounded

(tied) to the connector shell.

Intentional Radiator Modular Certification of the HS-1R

The HS-1R also contains an intentional radiator, the RFID transceiver. JADAK’s approach to

agency testing and certification for this was to get modular certification to facilitate easier

integration of the device into end user systems. In most circumstances the integrator will not

need to re-certify the intentional radiator, rather they can reference JADAK’s certifications listed

under the following:

Model Number: HS1RN4

Содержание Jadak Flexpoint HS-1R



















































































Результаты поиска

Содержание Jadak Flexpoint HS-1R

Отзывы:

Похожие инструкции для Jadak Flexpoint HS-1R

Бренды по названию

Популярные бренды

Novanta Jadak Flexpoint HS-1R, Руководство пользователя

Результаты поиска

Содержание Jadak Flexpoint HS-1R

Отзывы:

Похожие инструкции для Jadak Flexpoint HS-1R

Бренды по названию

Популярные бренды