NORTHROP GRUMMAN Iklwa II Скачать руководство пользователя страница 2

Страница: 2 / 6

SERVICE BULLETIN

Note No.

SVC-FSB-0050

Release Date

11/20/2017

Contact

[email protected]

SVC-FSB-0050 Iklwa II and Patara II

Shutter Assembly Repair Procedure

1.2.

Wipe off the outside of the laser.

1.3.

Put on powder free gloves.

1.4.

Ensure power is turned off to the laser and unplug laser from power source.

1.5.

Using a 3/32" hex driver, loosen the mounting hardware holding the laser cover to the
laser housing.

1.6.

Remove the cover.

Determine Failure Mechanism and Repair

Shutter assemblies shipped in lasers prior to May 2017 may encounter interference between
screws protruding through the disk and the solenoid when the shutter is in the open position.
See

Figures 1

and

below.

Figure 1: Protruding Screw

Figure 2: Protruding Screw – Close Up

2.1.

Ensure that none of the three mounting screw ends are visible between the solenoid
body and the thin disk, as seen in

Figures 1

and

above.

Screw Head Protruding

Causing Shutter to Bind

Screw Head Protruding

Causing Shutter to Bind

Disk

Solenoid

Содержание Iklwa II







Результаты поиска

Содержание Iklwa II

Отзывы:

Похожие инструкции для Iklwa II

Бренды по названию

Популярные бренды

NORTHROP GRUMMAN Iklwa II, Процедура ремонта

Результаты поиска

Содержание Iklwa II

Отзывы:

Похожие инструкции для Iklwa II

Бренды по названию

Популярные бренды