manualshive.com logo in svg

North Star M157593E, Руководство пользователя

Поделиться
Скачать
North Star M157593E Скачать руководство пользователя страница 34

Operation 

 

34 

pressure first and follow instructions for attaching a nozzle). 

2.

 

Clear the cleaning area of all persons.  Keep children and pets away. 

3.

 

Hold the spray gun firmly with two hands and a sturdy stance -- Gun 
kicks back when triggered. 

 

      

CAUTION

: 

Spray gun metal gets extremely hot when using 

the burner and can burn you on contact.  Never touch the metal 
screw or any metal parts of the spray gun when the heater is being 
used.  Use only designated grip areas. 

 
 
 
 
 

 

4.

 

Wash from the bottom to the top, using side-to-side motions.  This 
washes away heavy dirt and allows the detergent to soak as you work 
toward the top. 

5.

 

Use the width of the spray pattern to wash a wide path.  Overlap spray 
paths for complete coverage. 

6.

 

The nozzle should be 12" to 24" from the work, closer for tough areas. 

7.

 

Small parts should be washed in a basket so the pressure does not push 
them away.  Larger, lightweight parts should be clamped down. 

8.

 

The pressure washer is set and locked to the maximum rated pressure 
when it leaves the factory.  (See Figure 11 below) 

 

      

WARNING

: 

Do not attempt to alter the unloader valve's maximum 

pressure.  Excess pressure could cause serious injury from escaping high-
pressure fluids and/or pump damage.  Any alteration other than turning the 
adjustment knob will void your warranty. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

00417

 

Safety Latch 

 

Figure 11 

 

Unloader 

Содержание M157593E































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды