North Star M157593E Скачать руководство пользователя страница 12

Страница: 12 / 62

Assembly and Initial Set-Up

Step 2. Trailer Assembly

WARNING:

The pressure washer is heavy. It can crush and cause serious injury if it rolls out

of control or tips over. Follow all assembly instructions exactly as presented below.

1.)

Remove the top and four sides of the
steel crate.

2.)

Remove A-frame from trailer frame.
(Keep fasteners for step 7)

3.)

Slide A-frame into holders under trailer
frame (built into the front posts).

4.)

Install jack onto A-frame with 3/8x1"
bolts, 3/8" lock nuts, and washers
provided. Tighten to 37 ft.-lbs.

5.)

Slide caster wheel onto jack and secure
with pin.

6.)

Crank jack down until A-frame becomes
level (parallel to ground).

7.)

Attach A-frame to trailer frame with six
5/8" bolts, Class G nuts and washers.
Tighten to 180 ft.-lbs. Use a torque
wrench.

8.)

Check trailer light wire routing though
A-frame, make sure wires are not
pinched, stretched, or pass any rough
edges.

9.)

Crank jack down farther (so A-frame

goes up) to take weight off front
shipping posts.

10.)

Remove front shipping posts.

11.)

Crank jack up as far as it will go
(so A-frame goes down and weight is
applied to wheels)

12.)

Disconnect rear shipping posts from
frame (remove only the bolts at the top
of the rear shipping posts)

13.)

Roll trailer forward until it is free of the
rear shipping posts.

Front Shipping
Posts

Rear Shipping Posts

(one on each corner)

A-frame

Caster
wheel

Jack

Trailer
Frame

Front post

Содержание M157593E































































Результаты поиска

Содержание M157593E

Отзывы:

Бренды по названию

Популярные бренды

North Star M157593E, Руководство пользователя

Результаты поиска

Содержание M157593E

Отзывы:

Бренды по названию

Популярные бренды