Nortel 425-24T Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 488

Nortel 425-24T Скачать руководство пользователя страница 39

39

System Configuration Guide

Chapter 1
About Ethernet Switches 325 and 425

This chapter provides an introduction to the Ethernet switch software release 3.6.
This version of the Ethernet switch software supports the following devices:

•

Ethernet Switch 325

•

Ethernet Switch 425

This chapter describes the hardware components and features of the Ethernet
Switch 325/425, and covers the following topics:

•

“New features in software release 3.6”

•

“Hardware components of the Ethernet Switch 325” on page 57

•

“Hardware components of the Ethernet Switch 425” on page 67

•

“Network configuration examples” on page 83

•

“Stack operation” on page 87

New features in software release 3.6

The Ethernet Switch 325/425 provides wire-speed switching for
high-performance, low-cost connections to full-duplex and half-duplex
10/100/1000 Mb/s Ethernet Local Area Networks (LANs).

The following is the list of new features introduced in the Ethernet Switch 325/
425 software release 3.6.

•

“Link Layer Discovery Protocol (IEEE 802.1ab)” on page 40

•

“Ethernet Switch 425-48T stacking support” on page 44

•

“Username and password enhancement” on page 44

«
...
37
38
39
40
41
...
»

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов