manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 87 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 87

Chapter 1 About Ethernet Switches 325 and 425

87

System Configuration Guide

 

As shown in 

Figure 14

, the Ethernet Routing Switch 8600 switch is used as a 

backbone switch, connecting to the Ethernet Switch 425 with an optional 
(1000BASE-SX) GBIC for maximum bandwidth. The Ethernet Switch 425-24T 
and the Ethernet Switch 325-24T have 100 Mb/s connections to the Ethernet 
Switch 425-24T, a 100BASE-TX hub, and a 100 Mb/s server as well as 10 Mb/s 
connections to DTE (data terminal equipment). 

Figure 14   

Configuring power workgroups and a shared media hub

Stack operation

You can connect up to eight units of the Ethernet Switch 425-24T and Ethernet 
Switch 425-48T to provide uninterrupted connectivity for up to 392 ports. The 
entire stack can be managed as a single unit with a single IP and MAC address

You can select the base unit of the stack by using the momentary switch 
mechanism. It is recommended that you use only one base unit in the stack and the 
selection of the same should be done before powering the stack.

UI

UI Set

25

26

Spd: 

10/100/1000T Act: 

Activity

LED Status 

- 

Amber:10Mps 

Green:100 

Mps Blink:Activity

UI Cmd

Pwr

Console

Ethernet 

Switch 

325-24G

Spd Act

Spd Act

1

2

3

4

5

6

7

8

9

10

11

12

LED Status 

- 

Off:Half 

Duplex 

Green:Full 

Duplex

13

14

15

16

17

18

19

20

21

22

23

24

UI

UI Set

25

26

Spd: 

10/100/1000T Act: 

Activity

LED Status 

- 

Amber:10Mps 

Green:100 

Mps Blink:Activity

UI Cmd

Pwr

Console

Ethernet 

Switch 

325-24G

Spd Act

Spd Act

1

2

3

4

5

6

7

8

9

10

11

12

LED Status 

- 

Off:Half 

Duplex 

Green:Full 

Duplex

13

14

15

16

17

18

19

20

21

22

23

24

CPU PS1 PS2 FAN

Ethernt Switch 325-24G

Key

10 Mb/s

100 Mb/s

1000 Mb/s
(Gigabit)

Ethernet 

Switch

425-24T

Server

Ethernet Routing Switch 8600 

F

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов