Nortel 425-24T Скачать руководство пользователя страница 57

Страница: 57 / 488

Chapter 1 About Ethernet Switches 325 and 425

System Configuration Guide

Hardware components of the Ethernet Switch 325

Front panel

Figure 2

shows the front and side views of the Ethernet Switch 325.

Figure 2

Ethernet Switch 325-24G

Figure 3

shows the configuration of the front panel on the Ethernet Switch 325.

Table 2

describes the components on the front panel.

Figure 3

Ethernet Switch 325-24G front panel

UI Set

Spd: 10/100/1000T

Act: Activity

LED Status - Amber:10Mps Green:100 Mps Blink:Activity

UI Cmd

Pwr

Console

Spd Act

LED Status - Off:Half Duplex Green:Full Duplex

Ethernet Switch 325-24G

11108ER

Ethernet Switch 325-24G

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 57 / 488

Результаты поиска

Содержание 425-24T

Отзывы: