manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 44 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 44

44

Chapter 1 About Ethernet Switches 325 and 425

320985-A Rev 01

 

Configuring LLDP using the CLI

For information about configuring LLDP using the CLI, refer to 

“Configuring 

LLDP using the CLI” on page 300

.

Ethernet Switch 425-48T stacking support

With Release 3.6 software, the Ethernet Switch 425-48T can be stacked together 
with the Ethernet Switch 425-24T up to eight units high. You can stack the units 
using the Ethernet Switch 425 stack cables, which are available in 30 cm (1 foot) 
and 1 m (3 foot) lengths. These cables can be ordered separately (order number 
AL2018005 and AL2018006, respectively). 

For more information about stacking the Ethernet Switch 425-48T and Ethernet 
Switch 425-24T devices, see

 

“Stack operation” on page 87

. 

Username and password enhancement

With Release 3.6 software, you can use the CLI to set usernames as well as 
passwords for system access through the Console Interface, CLI, Telnet, and 
Web-based management. The syntax for the new 

username 

command is:

username <

username

> <

password

> [ro|rw] 

Note: 

With Release 3.6 software, the Ethernet Switches 425-24T and 

425-48T have stacking enabled by default, which means that ports 26 
and 50, respectively, are disabled by default. This is because the cascade 
port shares resources with port 26 on the Ethernet Switch 425-24T and 
port 50 on the Ethernet Switch 425-48T. Either the cascade port can be 
active, or port 26 or 50 can be active. 
If you want to use port 26 or port 50 in standalone mode, disable 
stacking and reboot the switch.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов