manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 83 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 83

Chapter 1 About Ethernet Switches 325 and 425

83

System Configuration Guide

 

Network configuration examples

This section provides network configuration examples using the Ethernet Switch 
325/425. In these examples, the packet classification feature can be used to 
prioritize the traffic of the network to ensure uninterrupted traffic of critical 
applications. The examples are:

•

“Desktop switch application”

•

“Segment switch application” on page 85

•

“High-density switched workgroup application” on page 86

Desktop switch application

Figure 10

 and 

Figure 11

 show the Ethernet Switch 325/425 used as a desktop 

switch. The desktop workstations are connected directly to switch ports.

Figure 10   

Ethernet Switch 325 used as a desktop switch

Up to 24 users

To

Network

Center

Key

10 Mb/s
100 Mb/s
1000 Mb/s

Ethernet 325-24G

10BASE-T hub

Before

After

Up to 24 users

To

Network

Center

11112EA

- 23 users share 10 Mb/s (10/24 Mb/s per user)
- Network center bottleneck (10 Mb/s bandwidth)

- 24 users; each with dedicated 100 Mb/s bandwidth
- Network center with dedicated 1 Gb/s full-duplex
  bandwith

UI

UI Set

25

26

Spd: 10/100/1000T Act: Activity

LED Status - Amber:10Mps Green:100 Mps Blink:Activity

UI Cmd

Pwr

Console

Ethernet Switch 325-24G

Spd Act

Spd Act

1

2

3

4

5

6

7

8

9

10

11

12

LED Status - Off:Half Duplex Green:Full Duplex

13

14

15

16

17

18

19

20

21

22

23

24

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов