background image

151B0801 R5 3/28/2006

 

12

TABLE A-1: BECKETT OIL BURNER SET-UP 

BECKETT AFG SERIES OIL BURNERS 

FURNACE 

MODEL

 

OUTPUT 

BTU/Hr.

 

BURNER 

MODEL

 

NOZZLE 

(Delavan)

 

PUMP 

PRESSURE

 

FLOW 

RATE

 

HEAD 

STATIC 

PLATE

 

58,100 

1, 2

 

AF76BO 

0.50 / 70° W 

100 PSIG 

0.50 GPH 

F0 

3-3/8 in. 

73,700 

2

 

AF76BN 

0.65 / 70° W 

100 PSIG 

0.65 GPH 

F3 

3-3/8 in. 

O4HD-091A 

78,900 

2

 

AF76BN 

0.70 / 70° W 

100 PSIG 

0.70 GPH 

F3 

3-3/8 in. 

87,700 

2

 

AF76BZHS 

0.75 / 70° W 

100 PSIG 

0.75 GPH 

F4 

3-3/8 in. 

98,800 

AF76BZHS 

0.85 / 70° W 

100 PSIG 

0.85 GPH 

F4 

3-3/8 in. 

O4HD-140A 

113,400 

AF76BZHS 

1.00 / 70° W 

100 PSIG 

1.00 GPH 

F4 

3-3/8 in. 

1

 F0 Head required for proper combustion.   

2

 Low Firing Rate Baffle required, Beckett Part No. 3708 

In the United States, the R. W. Beckett “AFG” Burner may be equipped with Beckett’s “Inlet Air Shut-Off”, Beckett Part No. AF/A 5861, to increase efficiency. It reduces the 
amount of air passing through the oil burner, combustion chamber, breeching, etc. up the chimney between burner cycles. 

NOTE: THE USE OF THIS CONTROL CAN OCCASIONALLY CAUSE POST COMBUSTION NOZZLE DRIP. 

 

TABLE A-2: DIRECT DRIVE BLOWER SET-UP 

BLOWER SET-UP 

COOLING CAPACITY 

0.20 in. w.c. 

0.50 in. w.c. 

FURNACE 

OUTPUT 

BTU/Hr. 

BLOWER 

MOTOR 

HP

 

Dip 

Switch/Speed 

Setting 

Dip 

Switch/Speed 

Setting 

Htg. CFM 

Range 

1

 

Tons 

2

 

MOTOR 

HP

 

Clg. CFM 

Range

 

58,100 Low 

Low 

668-1069 

73,700 Medium-Low 

Medium-Low 

841-1346 

O4HD-091A-12-

FA 

78,900 

10-10DD ½ 

Medium-High Medium-High  910-1456 

3 ½ 

1047-1267 

87,700 Low 

Low 

943-1458 

98,800 Low 

Medium-Low 

1084-1676 

O4HD-140A-16-

FA 

113,400 

11-10DD ¾ 

Low Medium-Low 

1279-1977 

5 ¾ 

1499-1879 

58,100 0-0-0 

0-0-0 

900 

73,700 1-0-1 

1-0-1 

1050 

O4HD-091A-V-F 

78,900 

11 10DD 

¾ 

1-0-0 1-0-0  1200 

3 ¾ 

312-1531 

87,700 1-0-0 

1-0-0 

1200 

98,800 0-1-1 

0-1-1 

1350 

O4HD-140A-V-F 

113,400 

11 10DD 

¾ 

0-1-0 0-1-0  1500 

5 ¾ 

312-1844 

(1)

 Heating Range values based on temperature rise. Upper values may exceed measured airflow values in Table A-3.      

(2)

 Nominal values only.

 

 

Содержание O4HD-091A-12-FA

































Отзывы: