Norac UC5 Rogator 600 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 31

background image

22

9

Software Setup

1.

Start up your sprayer and test the sprayer’s functionality. The display terminal does not
need to be powered on for the original boom function switches to operate. Unfold the
booms and raise/lower each boom and the main section.

Confirm that the cabling and hoses are agreeable to the entire range of motion.

2.

If any functions do not work, review the hydraulic and electrical portions of this manual to
check for proper installation.

3.

Turn on the power for the display terminal using the switch on the side.

4.

The procedure for the installation of the UC5 Spray Height Control system is now
complete. Begin the AUTOMATIC SYSTEM SETUP procedure as described in the UC5

Spray Height Control Operator’s Manual.

«
...
23
24
25
26
27
...
»

Содержание UC5 Rogator 600
































Отзывы:

Нет отзывов

Похожие инструкции для UC5 Rogator 600

Бренд: ABB Страницы: 138

Бренд: ABB Страницы: 116

Relion 615 series

Бренд: ABB Страницы: 136

Бренд: Balboa Instruments Страницы: 10

Бренд: Quantum Data Страницы: 36

Бренд: Eaton Страницы: 166

Бренд: GAUGEMASTER Страницы: 2

Бренд: EasyIO Страницы: 19

Бренд: Zero 88 Страницы: 2

Бренд: Zenit Страницы: 24

Бренд: Daikin Страницы: 56

Бренд: Danfoss Страницы: 36

Бренд: fakro Страницы: 16

Бренд: e-BLEACH Страницы: 24

Бренд: Hanna Instruments Страницы: 54

Бренд: Hanna Instruments Страницы: 2

Бренд: Veeder-Root Страницы: 27

Бренд: Valve Concepts Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды