38
6
APPENDIX A - INTERFACE CABLE MODIFICATION PROCEDURE
Some earlier models of John Deere sprayers
(4700 and 4710) may use a different style of
boom valve block with a different
arrangement of the connectors. As a result,
the NORAC 44658-01 interface cable (C12)
will need to be modified according to the
following instructions (See
Figure 37
and
Figure 38
for before and after schematics):
1.
Using the supplied GP Weatherpack pin
tool, carefully remove the blue/black wire
tee (Main Down) from the A-position of
the 4-pin flat connector tee (S4B & T4B).
The blue wire is attached to a black wire
that goes across the tee connection
(remove both ends of this tee).
2.
Insert blue/black wire tee from step 1
into the A-position of the 6-pin flat
connectors, M14 and M15 (S6C & T6C),
that are supplied in the zip lock bag with
the cable (these connectors are keyed on
the A and F position).
3.
Locate and remove the green wire (Left
Up) from the A-position of the 6-pin flat
shroud (S6B). Also remove the 5 black
wires from this tee (S6B & T6B). Use
these 5 wires to tee the remaining
positions of the two 6-pin connectors
(S6C & T6C) used in step 2 together
(B
B, C
C., D
D… etc). Remove the
cavity plug from the A-position of T6B for
use in step 4. After this step, there will
be 2 unused 6-pin flat connectors.
4.
Remove the black wire that goes across
the connection in the A-position of the 4-
pin square tee with the red wire (Right
Up) in the C-position (S4C & T4C).
Insert the green wire (Left Up) from step
3 into the A-position of the 4-pin shroud
(S4C). Seal the A-position on the 4-pin
tower (T4C) with the cavity plug
removed in step 3.
5.
Locate and remove the brown wire (Left
Down) from the A-position of the 6-pin
flat shroud (S6A). Remove the black wire
that goes across the connection in the A-
position of the 4-pin flat tee with the
white wire (Right Down) in the C-
position (S4D & T4D). Insert the brown
wire (Left Down) into the A-position of
the 4-pin shroud (S4D). A cavity plug will
be removed in step 6 that may be used to
seal the empty cavity created when
removing the black wire from the 4-pin
flat tower (T4D).
6.
Locate and remove the black wire (Main
Up) from the 4-pin square connector tee
(S4A & T4A). This black wire is attached
to a black tee wire similar to the wire
described in step 1. Insert black wire into
the A-position of the 6-pin flat assembly
removed in step 5 (S6A & T6A). This will
require removing the cavity plug installed
in the A-position of the 6-pin tower
(T6A). The cavity plug can then be used
to seal the empty socket created in step
5.
7.
The cable modifications are complete.
There should be 2 unused 6-pin flat
connectors, 2 black wires, an incomplete
4-pin square tee and an incomplete 4-pin
flat tee left over.
8.
Connect the modified harness to the
sprayer as indicated in
Figure 39
.
Содержание UC4 Plus Rogator 64 Series
